Stanley Black & Decker CS05, CS06 Tool Stickers & Tags, Danger, D A N G E R, I M P O R T A N T

TOOL STICKERS & TAGS

DANGER

Failure to use hydraulic hose labeled and certified as non-conductive when using hydraulic tools on or near electric lines may result in death or serious injury.

	For proper and safe operation read owners manual
	and mwke sure that you have been properly
ELECTROCUTION	trained in correct procedures required for work
	on or around electric lines.
HAZARD

12412

Electrical Warning Decal

D

30 LPM @ 138 B AR EHTMA CATEGORY

11207

Circuit Type D Decal

(CE Models Only)

28409 Composite Decal (CE Models Only)

Lwa
107
17784	28323
	CE Decal
101 Sound Level	(CE Models Only)
Decal
(CE Models Only)

4-6 GPM / 15-22 LPM

DO NOT EXCEED 2000 PSI / 140 BAR

DO NOT EXCEED SPECIFIED FLOW OR PRESSURE

USE CLOSED-CENTER TOOL ON CLOSED-CENTER

SYSTEM. USE OPEN-CENTER TOOL ON OPEN-CENTER

SYSTEM. CORRECTLY CONNECT HOSES TO TOOL “IN”

AND “OUT” PORTS. IMPROPER HANDLING, USE OR OTHER

MAINTENANCE OF TOOL COULD RESULT IN A LEAK, BURST

OR OTHER TOOL FAILURE. CONTACT AT A LEAK OR BURST

CAN CAUSE OIL INJECTION INTO THE BODY. FAILURE TO

OBSERVE THESE PRECAUTIONS CAN RESULT IN SERIOUS

PERSONAL INJURY.

03782

GPM Decal – CS05 Model

03786	13907
GPM Decal – CS06 Model (Not Shown)	Kickback Warning Decal

Stanley Hydraulic Tools

3810 SE Naef Road

Milwaukie, OR 97062

Model

07636 Name Tag

THIS CHAIN SAW IS EQUIPPED WITH AN AUTOMATIC CHAIN OILER.

SEE YOUR PARTS & SERVICE BOOK FOR PROPER ADJUSTING PROCEDURES

04746

Auto Oiler Decal

D A N G E R

1.	FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTI-
	FIED AS NON-CONDUCTIVE WHEN USING HYDRAULIC
	TOOLS ON OR NEAR ELECTRICAL LINES MAY RESULT IN
	DEATH OR SERIOUS INJURY.
	BEFORE USING HOSE LABELED AND CERTIFIED AS NON-
	CONDUCTIVE ON OR NEAR ELECTRIC LINES BE SURE THE
	HOSE IS MAINTAINED AS NON-CONDUCTIVE. THE HOSE
	SHOULD BE REGULARLY TESTED FOR ELECTRIC CURRENT
	LEAKAGE IN ACCORDANCE WITH YOUR SAFETY DEPART-
	MENT INSTRUCTIONS.
2.	A HYDRAULIC LEAK OR BURST MAY CAUSE OIL INJECTION
	INTO THE BODY OR CAUSE OTHER SEVERE PERSONAL
	INJURY.
	A. DO NOT EXCEED SPECIFIED FLOW AND PRESSURE
	FOR THIS TOOL. EXCESS FLOW OR PRESSURE MAY
	CAUSE A LEAK OR BURST.
	B. DO NOT EXCEED RATED WORKING PRESSURE OF
	HYDRAULIC HOSE USED WITH THIS TOOL. EXCESS
	PRESSURE MAY CAUSE A LEAK OR BURST.
	C. CHECK TOOL HOSE COUPLERS AND CONNECTORS
	DAILY FOR LEAKS. DO NOT FEEL FOR LEAKS WITH

D A N G E R

	D. DO NOT LIFT OR CARRY TOOL BY THE HOSES. DO
	NOT ABUSE HOSE. DO NOT USE KINKED, TORN OR
	DAMAGED HOSE.
3.	MAKE SURE HYDRAULIC HOSES ARE PROPERLY CON-
	NECTED TO THE TOOL BEFORE PRESSURING SYSTEM.
	SYSTEM PRESSURE HOSE MUST ALWAYS BE CON-
	NECTED TO TOOL “IN” PORT. SYSTEM RETURN HOSE
	MUST ALWAYS BE CONNECTED TO TOOL “OUT” PORT.
	REVERSING CONNECTIONS MAY CAUSE REVERSE
	TOOL OPERATION WHICH CAN RESULT IN SEVERE
	PERSONAL INJURY.
4.	DO NOT CONNECT OPEN-CENTER TOOLS TO CLOSED-
	CENTER HYDRAULIC SYSTEMS. THIS MAY RESULT IN
	LOSS OF OTHER HYDRAULIC FUNCTIONS POWERED BY
	THE SAME SYSTEM AND/OR SEVERE PERSONAL INJURY.
5.	BYSTANDERS MAY BE INJURED IN YOUR WORK AREA.
	KEEP BYSTANDERS CLEAR OF YOUR WORK AREA.
6.	WEAR HEARING, EYE, FOOT, HAND AND HEAD PRO-
	TECTION.
7.	TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE,
	ALL TOOL REPAIR MAINTENANCE AND SERVICE MUST

NOTE

THE INFORMATION LISTED ON THE

STICKERS SHOWN, MUST BE LEGIBLE AT ALL

TIMES.

REPLACE DECALS IF THEY BECOME WORN

OR DAMAGED. REPLACEMENTS ARE

AVAILABLE FROM YOUR LOCAL STANLEY

DISTRIBUTOR.

The safety tag (P/N 15875) at right is attached to the tool when shipped from the factory. Read and understand the safety instructions listed on this tag before removal. We suggest you retain this tag and attach it to the tool when not in use.

YOUR HANDS. CONTACT WITH A LEAK MAY RESULT

IN SEVERE PERSONAL INJURY.

I M P O R T A N T

READ OPERATION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT.

USE ONLY PARTS AND REPAIR PROCEDURES APPROVED BY STANLEY AND DESCRIBED IN THE OPERATION MANUAL.

TAG TO BE REMOVED ONLY BY

TOOL OPERATOR.

SEE OTHER SIDE

ONLY BE PERFORMED BY AUTHORIZED AND PROPERLY

TRAINED PERSONNEL.

I M P O R T A N T

READ OPERATION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT.

USE ONLY PARTS AND REPAIR PROCEDURES APPROVED BY STANLEY AND DESCRIBED IN THE OPERATION MANUAL.

TAG TO BE REMOVED ONLY BY

TOOL OPERATOR.

SEE OTHER SIDE

SAFETY TAG P/N 15875 (Shown smaller then actual size)

CS05/CS06 User Manual ◄ 9