HOSE TYPES

The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are:

Certified non-conductive— constructed of thermoplastic or synthetic rubber inner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. Hose labeled certified non- conductive is the only hose authorized for use near electrical conductors.

Wire-braided(conductive) — constructed of synthetic rubber inner tube, single or double wire braid reinforce- ment, and weather resistant synthetic rubber cover. This hose is conductive and must never be used near electrical conductors.

Fabric-braided(not certified or labeled non-conductive) — constructed of thermoplastic or synthetic rubber in- ner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. This hose is not certified non-conductiveand must never be used near electrical conductors.

HOSE SAFETY TAGS

To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS.

If the information on a tag is illegible because of wear or damage, replace the tag immediately. A new tag may be obtained from your Stanley Distributor.

THE TAG SHOWN BELOW IS ATTACHED TO “CERTIFIED NON-CONDUCTIVE” HOSE

 

 

 

 

 

 

 

 

 

 

 

 

A G

 

D A N G E R

 

 

 

 

 

 

D A N G E R

 

T

 

 

 

 

 

 

 

 

 

 

I S

 

1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

 

 

 

 

 

3.

DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE

 

H

 

WHEN USING HYDRAULIC TOOLS ON OR NEAR ELECTRIC LINES MAY RESULT IN

 

 

 

 

 

 

OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE.

 

T

 

DEATH OR SERIOUS INJURY.

 

 

 

 

 

 

KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT

 

VE

 

FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROP-

 

 

 

 

 

 

CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION

 

 

 

 

 

 

 

 

AND SEVERE PERSONAL INJURY.

 

O

 

ERLY TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND

 

 

 

 

 

 

 

 

 

ELECTRIC LINES.

 

 

 

 

 

4.

HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, ABRASION, CUTTING, OR

 

M

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT

 

E

 

 

 

 

 

 

 

 

 

 

2. BEFORE USING HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

 

 

 

 

 

 

USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

 

R

 

 

 

 

 

 

 

 

 

ON OR NEAR ELECTRIC LINES. WIPE THE ENTIRE LENGTH OF THE HOSE AND FIT-

 

 

 

 

 

5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAM-

 

T

 

 

 

 

 

 

 

 

TING WITH A CLEAN DRY ABSORBENT CLOTH TO REMOVE DIRT AND MOISTURE AND

 

 

 

 

 

 

 

 

 

 

 

 

 

AGE TO COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE

 

N O

 

TEST HOSE FOR MAXIMUM ALLOWABLE CURRENT LEAKAGE IN ACCORDANCE WITH

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IMMEDIATELY. NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

 

 

SAFETY DEPARTMENT INSTRUCTIONS.

 

 

 

 

 

6.

 

D O

 

 

 

 

 

 

 

AFTER EACH USE STORE IN A CLEAN DRY AREA.

 

 

SEE OTHER SIDE

 

 

 

 

 

 

SEE OTHER SIDE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SIDE 2

 

 

 

SIDE 1

 

 

 

 

 

 

(Shown smaller than actual size)

THE TAG SHOWN BELOW IS ATTACHED TO “CONDUCTIVE” HOSE.

D O N O T R E M O V E T H I S T A G

D O N O T R E M O V E T H I S T A G

 

D A N G E R

 

 

D A N G E R

 

 

 

 

 

1.

DO NOT USE THIS HYDRAULIC HOSE ON OR NEAR ELECTRIC LINES. THIS HOSE IS

5.

CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAMAGE TO

 

NOT LABELED OR CERTIFIED AS NON-CONDUCTIVE. USING THIS HOSE ON OR NEAR

 

COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY.

 

ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.

 

NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

2.

FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROPERLY

6.

AFTER EACH USE STORE IN A CLEAN DRY AREA.

 

TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND ELEC-

 

 

 

TRIC LINES.

 

 

3.DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION AND SEVERE PERSONAL INJURY.

4.HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, CUTTING, OR CONTACT

WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

 

 

SEE OTHER SIDE

 

 

 

 

 

SEE OTHER SIDE

 

 

 

 

SIDE 1

 

 

 

 

 

SIDE 2

 

 

 

(Shown smaller than actual size)

D O N O T R E M O V E T H I S T A G

8 ► MHP3 Diesel User Manual

Page 7 Page 9
Page 8
Image 8
Stanley Black & Decker MHP3 manual Hose Types, Hose Safety Tags
Page 7 Page 9

MHP3 specifications

Stanley Black & Decker has long been a leader in the tools and hardware industry, and their MHP3 model exemplifies the brand's commitment to innovation and quality. The MHP3 is a multi-use power tool, expertly designed to meet the rigorous demands of both professionals and DIY enthusiasts alike.

One of the standout features of the MHP3 is its powerful motor, delivering robust performance for a variety of tasks. With variable speed control, users can easily adjust the tool's power to suit specific applications, ensuring optimal results whether drilling, fastened, or cutting. The ergonomic design of the MHP3 ensures a comfortable grip, reducing fatigue during prolonged use.

The MHP3 incorporates advanced cordless technology, which adds a layer of convenience and mobility for users. Powered by a high-capacity lithium-ion battery, it offers extended run times and can be charged quickly, allowing for minimal downtime on jobs. The battery life indicator is a thoughtful addition, helping users monitor remaining power and plan their tasks accordingly.

Another remarkable characteristic of the MHP3 is its versatility. It comes with interchangeable attachments, allowing users to tackle a multitude of projects without needing multiple tools. This adaptability makes it a favorite among professionals who require a reliable tool that can efficiently manage different jobs on-site. The tool's compatibility with a wide array of accessories further enhances its functionality.

Safety features are paramount in tool design, and Stanley Black & Decker has ensured that the MHP3 is equipped with several. The integrated safety switch prevents accidental startups, while the durable outer casing protects internal components from damage during rigorous use.

In addition to its functional capabilities, the MHP3 is also designed with aesthetics in mind. With a modern and sleek profile, it fits well in any tool collection while being practical for everyday use.

Overall, the Stanley Black & Decker MHP3 stands out as a comprehensive power tool solution. Its combination of power, versatility, and safety features makes it an indispensable addition to any workshop or job site, embodying the brand's commitment to delivering quality tools that meet the needs of consumers across various sectors. Whether you're a seasoned professional or just starting on home improvement projects, the MHP3 is engineered to deliver outstanding performance and reliability.
Top Page Image Contents