Star Trac none manual Assembly and Setup Adjustable DEC/AB Bench, Assemble the Adjusting Post

3. Install the Leg Cushions

Slide the leg cushion shaft (5) through the guide hole in the main frame (1), centering the shaft in the frame. Secure the leg cushion shaft in the main frame using one screw (27).

Install one plastic spacer (18), one leg cushion

(15)and one plastic spacer (18) on the leg cushion shaft (5). Secure the leg cushion to the leg cushion shaft using one screw (30), spring washer (37), washer (34) and collar (19). Tighten the screw securely.

Repeat for the remaining leg cushion (15).

	19	30
	18	37
5	15	34
	18

1

27

18

15

18

19

34

37

30

31

ASSEMBLY AND SETUP - ADJUSTABLE DEC/AB BENCH

PARTS AND MATERIALS

The following parts are included with the STAR TRAC INSTINCT ADJUSTABLE DEC/AB BENCH:

1	Frame, Main	1	23	Collar	2
2	Frame, Bench	1	25	Screw, Socket Head Cap, 8X20M	1
3	Post, Adjusting	1	27	Screw, Button Head Socket Cap, 10X130M	2
5	Foot, Front	1	29	Screw, Button Head Socket Cap, 10X35M	4
6	Foot, Rear	1	30	Screw, Button Head Socket Cap, 10X25M	5
7	Shaft, Leg Cushion	1	32	Lock Nut, Nylon Insert, 10M	8
9	Screw	3	33	Washer, 11M	13
10	Cushion, Back	1	34	Washer, 13M	6
14	Cushion, Leg	2	36	Washer, Spring, 10M	5
22	Spacer, Plastic	4

TOOLS REQUIRED

Most STAR TRAC INSTINCT machines can be assembled using the following tools:

4. Assemble the Adjusting Post

Align the two drilled holes in the left handle

(2) with the mating holes in the adjusting post
(6). Insert two screws (31) with washers (34)
through the handle and post to maintain the
parts in	position. Slide the right handle (3)
onto the	two screws (31), and secure the post

34

2

6

■Metric Hex Key Wrenches - 2.5mm, 5mm, 6mm, 8mm, 10mm

■Metric Open-End Wrenches - 10mm, 15mm, 17mm

■Metric Ratchet Socket Wrench Set (including 17mm sock- et)

■Torque Wrench

■Channel Lock Pliers

■Vice Grip Pliers

■Rubber Mallet

■Phillips Head Screwdriver - #2

and handles together using two washers (34)

and lock nuts (32). Tighten the nuts securely.

5. Install the Left and Right Cushions

Slowly slide the adjusting post (6) into the post guide in the main frame (1). While holding the adjusting post, press the ratchet handle to retract the locking pin, and slide the post fully into the post guide.

Release the ratchet handle. Slowly slide the adjusting post out of the main frame until the locking pin on the ratchet handle locks into a drilled hole in the adjusting post.

Hold the right cushion (11) in place on the Adjusting post (6). Secure the cushion to the adjusting post using two screws (29) and washers (34). Tighten the screws securely.

Repeat for the left cushion (12).

You have now completed assembly of your INSTINCT 45º BACK EXTENSION BENCH.

34

32

3

12

11

634

1

29 34

29

Your INSTINCT ADJUSTABLE DEC/AB BENCH includes a hex key set and combination open-end wrench.

SITING REQUIREMENTS

Your INSTINCT ADJUSTABLE DEC/AB BENCH requires approximately __ square feet of floor space to ensure safe operation of the unit.

UNPACKING

Your INSTINCT ADJUSTABLE DEC/AB BENCH is shipped in one or more shipping cartons. Each carton will generally con- tain one subassembly of the entire unit. To unpack:

■Remove the shipping straps from the outside of each shipping carton.

■Open the top of each carton and fold back all four flaps.

■Remove the packing materials, foam inserts, and ALL parts from each shipping carton. Keep the contents of each carton in a separate area to facilitate assembly. To ensure personal safety during assembly, place all packing materials outside the assembly area.

■Verify that all parts listed above are included in your shipment.

Take time now to enter your INSTINCT ADJUSTABLE DEC/AB BENCH serial number in the space below. If parts are miss- ing, or if you have any operational questions, please call Star Trac’s Service department at (800) 503-1221; have your serial num- ber ready.

Serial No. __________________________________________

10 STAR TRAC INSTINCT ADJUSTABLE BENCHES OWNER’S MANUAL STAR TRAC INSTINCT ADJUSTABLE BENCHES OWNER’S MANUAL 11