State Industries GPG85 650 NEA Low-NOxCommercial Gas Water Heaters, Titan Powered Burner, Phone

TITAN™ POWERED

BURNER

Low-NOx Commercial Gas Water Heaters

CAPACITY, INPUT AND OUTPUT

				FIRST		RECOVERY-GALLONS
	BTU					PER HOUR AT °F
				HOUR
						TEMPERATURE RISE
	INPUT	Gallons		RATING	GPH
MODEL			TANK			40°F	100°F	140°F
	PER	or		100° F	or
NUMBER	HOUR	Litres	SIZE	RISE	LPH	4°C	56°C	78°C
GPG85 540 NEA	540,000	U.S. Gallons	85	583	GPH	1309	523	374
GPV85 540 NEA		Litres	321.7	2206.7	LPH	4954.6	1979.6	1415.6
GPG85 650 NEA	650,000	U.S. Gallons	85	690	GPH	1579	630	450
GPV85 650 NEA		Litres	321.7	2611.7	LPH	5976.5	2384.6	1703.3
GPG85 740 NEA	740,000	U.S. Gallons	85	778	GPH	1794	718	512
GPV85 740 NEA		Litres	321.7	2944.7	LPH	6790.3	2717.6	1937.9

Based on 80% Thermal Efficiency obtained in State engineering laboratories.

To compensate for effects of high altitude above 2,000 feet, recovery ratings should be reduced 5% for every 1,000 feet above sea level.

Current Draw (120V, 60Hz, 1 Phase): 6.0 Amps

DIMENSIONS AND WEIGHT – ALL MODELS

Inches				DIMENSIONS						GAS	SHIPPING
or
	A	B	C	D	E	F	G	H	I	CONN.***	WEIGHT
CM
Inches	80-3/4	73	32-1/4	9	26-1/2	26-1/2	93	29-1/2	48-1/2	1˝	950 Lbs.
CM	205.1	185.4	81.9	22.9	67.3	67.3	236.2	74.9	123.2	-	431.8 Kg

*D dimension is for atmospheric vent size (GPG models).

**E dimension is for direct and sidewall vent size (GPV models).

***Minimum gas supply pipe is 1-1/4". See Reference Manual, Table 7 for gas supply pipe size.

SUGGESTED SPECIFICATION

Water heater(s) shall be State Model ________________ or equal, with maximum storage capacity of 85

gallons, an input rating of ___________________ BTU/Hr., a recovery rating of ____ GPH at 100ºF temperature

rise, and minimum thermal efficiency of 80%. Heater(s) shall meet ASHRAE/IESNA 90.1-1999 requirements for thermal efficiency and standby loss, and meet SCAQMD R1146.2 low-NOx requirements. In addition, heater(s) shall: 1) Include a powered gas burner, redundant main gas valves, gas pressure regulator and flame inspection port. 2) Include a high-temperature limit control, dual-bulb thermostat for accurate temperature control and anti- stacking compensation and a factory-installed AGA rated temperature and pressure relief valve. 3) Be equipped with 1-1/2" NPT water inlet and outlet and a boiler-type handhole cleanout. 4) Shall be constructed and stamped in accordance with ASME Boiler and Pressure Vessel Code and be so marked for a maximum working pressure of 160 psi. 5) Have a glass-lined steel tank with multiple anodes for corrosion protection, and polyurethane foam insulation. 6) Tank shall have a 3-year limited warranty against corrosion as outlined in the written warranty.

Venting: GPG heater(s) shall be supplied with a Barometric Draft Regulator for conventional atmospheric venting.

GPV heater(s) shall be supplied with an optional vent kit allowing for horizontal sidewall venting or direct venting.

Burner and Controls: Burner(s) shall be pre-mix design, with internal FGR and thermal cutoff, separate spark pilot ignition system, integral blocked flue sensor, glass view port, main gas regulator, automatic gas valve, manual test cock and manual gas shutoff. Burner(s) must be factory-installed, tested and started by an Authorized State Start- up Agent before being placed into operation.

For complete information on limited warranties, consult written warranty, or contact the State Customer Care Center, 1-800-365-0024.

State Industries, Inc. reserves the right to make product changes or improvements without prior notice.

For Additional Technical Information,

PHONE 800-365-0024

STATE WATER HEATERS

500 Tennessee Waltz Parkway, Ashland City, TN 37015 www.statewaterheaters.com

Page 2 of 2

SCGSS00205	© 2005 State Industries, Inc.	Printed in U.S.A.
March 2007R