Manuals / State Industries / Household Appliance / Water Heater

State Industries Green Choice instruction manual Chart #3 GAL CAP, BTU’s in 1000’s NAT./L.P

Models: Green Choice

1 44
Download 44 pages 12.75 Kb
Page 14
Image 14

Optional Vertical Vent Kit with Standard Horizontal Vent Kit - Installation #2

Any Optional Vent Kit

*Each part is stamped with a part number.

The opening through the wall should be cut at this time. If this has not been done, refer to “Cutting The Opening Through The Outside Wall,” onpage11.

1.First it must be determined how far the vertical 3” (76 mm) diameter telescoping flue sections are set and locked together using the two screws supplied.

FIGURE 31 .

Use chart #3, drawing and simple equation below, to find the length of expansion of the telescoping flue sections. Because of manufacturing tolerances, place the telescoping extension on the water heater and adjust the height (“X” Dimension) and mark the point. Once the length has been determined, lock the two sections together by drilling two holes (180° apart) in the pipe and securing with the screws supplied.

FIGURE32.

CHART #3

*GAL CAP.

*BTU’s in 1000’s - NAT./L.P.

 

A

40

36/36

48 3/4”

 

124 cm

 

50

38/38

57 1/2”

 

146 cm

40

40/40

48 3/4”

 

124 cm

50

48/44

61”

 

155 cm

75

55 NAT.

63”

 

160 cm

 

 

 

 

 

*Check the model and rating plate attached to the water heater for specific model number and other detailed information.

2.Set the vertical 3” (76 mm) diameter telescoping flue section in place on the flue collar. Using a # 22 drill bit, drill two holes (180° apart) and secure the vertical assembly to the flue collar.

FIGURE33.

3.Slide the 6” (152 mm) vent telescoping section apart to reveal the beads. Using the caulking supplied, fill the beads.

FIGURE34.

4. Apply an ample amount of sealant around the oval flare of the jacket.

FIGURE 35.

5.Place the 6” (152 mm) vent section over the 3” (76 mm) flue section. Subtract 3/4” (19 mm) from the predetermined “X” dimension. This determines the length of the 6” (152 mm) vent extension. Slide the 6” (152 mm) vent extension apart to this dimension and secure with the two screws supplied.

FIGURE36.

6.Form the round end of the 6” (152 mm) vent extension to the top of the jacket and secure with four sheet metal screws.

FIGURE 37.

14

Page 13 Page 15
Page 14
Image 14
State Industries Green Choice instruction manual Chart #3 GAL CAP, BTU’s in 1000’s NAT./L.P
Page 13 Page 15

Green Choice specifications

State Industries Green Choice is a remarkable initiative designed to promote energy efficiency and environmentally-friendly practices in the manufacturing sector. The program focuses on providing high-efficiency appliances and heating systems that are not only cost-effective but also reduce environmental impact. With a growing concern about climate change, State Industries aims to address these issues through innovations in technology and sustainable practices.

One of the main features of the Green Choice initiative is its commitment to producing ENERGY STAR® certified products. These appliances meet strict energy efficiency guidelines set by the U.S. Environmental Protection Agency, helping consumers save money on energy bills while also decreasing their carbon footprint. By prioritizing energy efficiency, State Industries ensures that their products move the industry toward a more sustainable future.

Incorporating advanced technologies is central to the Green Choice initiative. The use of state-of-the-art insulation materials minimizes heat loss, while high-efficiency burners and heat exchangers maximize energy utilization in heating systems. These technological innovations lead to significant reductions in energy consumption, translating to both financial savings for consumers and reduced greenhouse gas emissions.

Another characteristic of Green Choice is the emphasis on using sustainable materials in manufacturing. State Industries strives to source materials that are either recyclable or derived from renewable resources. This commitment not only supports the economy but also minimizes waste and environmental degradation associated with traditional manufacturing processes.

Furthermore, State Industries prioritizes lifecycle analysis in the development of its products. This approach evaluates the environmental impact of a product from its conception through production, usage, and eventual disposal. By understanding the full lifecycle, State Industries can make informed decisions that enhance the sustainability of its offerings.

Consumer education is also a vital component of the Green Choice program. State Industries actively engages with customers to raise awareness about energy-efficient practices and the benefits of choosing sustainable products. By empowering consumers with knowledge, the initiative encourages responsible energy use and promotes a culture of sustainability.

In conclusion, State Industries Green Choice represents a holistic approach to manufacturing, focusing on energy efficiency, technological innovation, sustainable materials, and consumer engagement. This initiative not only helps to combat environmental issues but also fosters a market for eco-friendly products, paving the way for a more sustainable future. State Industries is setting a positive example in the industry by prioritizing ecological responsibility while delivering high-quality, efficient solutions to consumers.