Manuals / State Industries / Household Appliance / Water Heater

State Industries Green Choice instruction manual Filling the Water Heater GAS Piping

Models: Green Choice

1 44
Download 44 pages 12.75 Kb
Page 27
Image 27

If after manually operating the valve, it fails to completely reset and continues to release water, immediately close the cold water inlet to the water heater, follow the draining instructions, and replace the temperature-pressure relief valve with a new one.

FIGURE106.

FILLING THE WATER HEATER

GAS PIPING

Make sure the gas supplied is the same type listed on the model rating plate. The inlet gaspressuremustnotexceed14inch watercolumn(2.6kPa) for natural and propane gas (L.P.). The minimum inlet gas pressure shown on the rating plate is that which will permit firing at rated input.

If the gas control valve is subjected to pressures exceeding 1/2 pound per square inch (3.5 kPa), the damage to the gas control valve could result in a fire or explosion from leaking gas.

If the main gas line Shut-off serving all gas appliances is used, also turn “off” the gas at each appliance. Leave all gas appliances shut “off” until the water heater installation is complete.

A gas line of sufficient size must be run to the water heater. Consult the current edition of National Fuel Gas CodeANSI Z223.1/NFPA54 and your gas supplier concerning pipe size.

There must be:

Never use this water heater unless it is completely full of water. To prevent damage to the tank, the tank must be filled with water. Water must flow from the hot water faucet before turning “ON” gas to the water heater.

To fill the water heater with water:

1.Close the water heater drain valve by turning the handle to the right (clockwise). The drain valve is on the lower front of the water heater.

2.Open the cold water supply valve to the water heater.

NOTE: The cold water supply valve must be left open when the water heater is in use.

3.To insure complete filling of the tank, allow air to exit by opening the nearest hot water faucet. Allow water to run until a constant flow is obtained. This will let air out of the water heater and the piping.

4.Check all water piping and connections for leaks. Repair as needed.

•A readily accessible manual shut off valve in the gas supply line serving the water heater, and

•A drip leg (sediment trap) ahead of the gas control valve to help prevent dirt and foreign materials from entering the gas control valve.

•A flexible gas connector or a ground joint union between the shut off valve and control valve to permit servicing of the unit.

Be sure to check all the gas piping for leaks before lighting the water heater. Use a soapy water solution, not a match or open flame. Rinse off soapy solution and wipe dry.

27

Page 26 Page 28
Page 27
Image 27
State Industries Green Choice instruction manual Filling the Water Heater GAS Piping
Page 26 Page 28

Green Choice specifications

State Industries Green Choice is a remarkable initiative designed to promote energy efficiency and environmentally-friendly practices in the manufacturing sector. The program focuses on providing high-efficiency appliances and heating systems that are not only cost-effective but also reduce environmental impact. With a growing concern about climate change, State Industries aims to address these issues through innovations in technology and sustainable practices.

One of the main features of the Green Choice initiative is its commitment to producing ENERGY STAR® certified products. These appliances meet strict energy efficiency guidelines set by the U.S. Environmental Protection Agency, helping consumers save money on energy bills while also decreasing their carbon footprint. By prioritizing energy efficiency, State Industries ensures that their products move the industry toward a more sustainable future.

Incorporating advanced technologies is central to the Green Choice initiative. The use of state-of-the-art insulation materials minimizes heat loss, while high-efficiency burners and heat exchangers maximize energy utilization in heating systems. These technological innovations lead to significant reductions in energy consumption, translating to both financial savings for consumers and reduced greenhouse gas emissions.

Another characteristic of Green Choice is the emphasis on using sustainable materials in manufacturing. State Industries strives to source materials that are either recyclable or derived from renewable resources. This commitment not only supports the economy but also minimizes waste and environmental degradation associated with traditional manufacturing processes.

Furthermore, State Industries prioritizes lifecycle analysis in the development of its products. This approach evaluates the environmental impact of a product from its conception through production, usage, and eventual disposal. By understanding the full lifecycle, State Industries can make informed decisions that enhance the sustainability of its offerings.

Consumer education is also a vital component of the Green Choice program. State Industries actively engages with customers to raise awareness about energy-efficient practices and the benefits of choosing sustainable products. By empowering consumers with knowledge, the initiative encourages responsible energy use and promotes a culture of sustainability.

In conclusion, State Industries Green Choice represents a holistic approach to manufacturing, focusing on energy efficiency, technological innovation, sustainable materials, and consumer engagement. This initiative not only helps to combat environmental issues but also fosters a market for eco-friendly products, paving the way for a more sustainable future. State Industries is setting a positive example in the industry by prioritizing ecological responsibility while delivering high-quality, efficient solutions to consumers.