State Industries SDV100-260 BTU Input, Approx, Per Hour, Recovery, Gal, Model Number Cap Natural

Commercial Gas Water Heater

Sandblaster® Force™ gas water heaters are design certified by the CSA International as Automatic Circulating and Automatic storage water heaters. When used singly or in manifolded multiples with additional heaters or storage tanks, they can provide an independent hot water system. When installed with a mixing valve, they can provide both 140°F general use hot water and 180°F sanitizing hot water simultaneously.

SDV80 140, SDV100 199, SDV100 260 and SDV100 400 models meet or exceed Federal Efficiency Requirements prescribed by the Energy Policy and Conservation Act of 1992 (EPACT) for commercial water heaters. They also meet or exceed ASHRAE 90.1b-1992.

SDV75 70 meets or exceeds Federal Energy Efficiency Standards effective January 1, 1990, according to the National Appliance Energy Conservation Act (NAECA) of 1987.

Manufactured under one or more of the following U.S. Patent Numbers: 4,157,077; 4,263,879; 4,447,377; 4,527,543 and other patents pending. Canadian Patent Numbers 1,151,480; 1,215,276 and other Canadian patents pending.

In keeping with our policy of continuous product improvement, specifications are subject to change without prior notice.

		BTU Input		First Hour														Approx.
		Per Hour		Delivery	Recovery						Dimensions in Inches							Shipping
	Gal.																Gas	Weight
Model Number	Cap.	Natural	Propane	100° Rise	80°	100°	140°	A	B	C	D	E	F	G	H	I	Conn.	(lbs.)
SDV75 70NE	75	70,000	–	117	81	64	46	695⁄8	615⁄8	26	165⁄8	3	–	–	2	54	1⁄2˝	352
SDV75 70PE	75	–	65,000	112	74	59	42	695⁄8	615⁄8	26	165⁄8	3	–	–	2	54	1⁄2˝	352
SDV80 140NE•	80	140,000	140,000	200	180	144	103	761⁄4	717⁄8	28	83⁄4	3	201⁄4	615⁄8	21⁄4	565⁄8	3⁄4˝	645
SDV100 199NE*†•	100	199,000	–	276	258	206	147	747⁄8	701⁄2	301⁄4	83⁄4	3	201⁄4	601⁄8	21⁄4	551⁄8	3⁄4˝	825
SDV100 199PE*†•	100	–	190,000	266	245	196	140	747⁄8	701⁄2	301⁄4	83⁄4	3	201⁄4	601⁄8	21⁄4	551⁄8	3⁄4˝	825
SDV100 260NE•	100	260,000	260,000	338	335	268	191	791⁄2	771⁄2	301⁄4	83⁄4	4	193⁄4	611⁄2	21⁄4	56	3⁄4˝	900
SDV100 260NE ASME•	100	260,000	260,000	338	335	268	191	791⁄2	771⁄2	301⁄4	83⁄4	4	193⁄4	611⁄2	21⁄4	56	3⁄4˝	1010
SDV100 400NE	95	390,000	390,000	461	493	395	282	821⁄4	801⁄4	301⁄4	83⁄4	4 or 6+	213⁄4	631⁄2	21⁄4	58	1˝**	900
SDV100 400NE ASME	95	390,000	390,000	461	493	395	282	821⁄4	801⁄4	301⁄4	83⁄4	4 or 6+	213⁄4	631⁄2	21⁄4	58	1˝**	1100

First-Hour Delivery and Recoveries are rounded to nearest gallon. Model SDV75 70 has 3 ⁄4-inch water connections; all others have 11⁄2-inch. Dimensions are rounded to nearest 1⁄4-inch.

When ordering propane, change “N” to “P” in model number (SDV80 140PE). All models available in Canada. When ordering, add “CGA” to model number (SDV75 70NE CGA).

*Rear plumbing.

**Gas connection on Propane models is 3 ⁄4-inch.

†ASME construction not available.

•NSF construction available, add 5 ˝ to height and add NSK to model number (SDV80 140NE NSK).

+Vent diameter depends on length of run. 4 ˝ diameter up to 40 equivalent feet each run.

C

HOT

OUTLET

E COLD INLET

4˝
AIR	EXHAUST
INTAKE

I B A

D H

SDV75 70 SDV80 140, SDV100 199, SDV100 260 & SDV100 400

Venting System Requirements

1The water heater requires its own (separate) venting system.

2Venting cannot be connected to existing vent piping or chimney.

3Venting may terminate vertically or horizontally to the outdoors.

4Vertical and horizontal vent runs must be secured at 31⁄2´ intervals.

5Vent piping cannot under any circumstances be run downhill.

6Horizontal runs require a minimum 1⁄4˝ rise per foot.

7Vent pipes must be installed so that they can be visually inspected.

SDV Series	Maximum Equivalent Feet of Pipe With One 90° Elbow
Models	3" Schedule 40 PVC	4" Schedule 40 PVC*	6" Schedule 40 PVC*
SDV75-70	50'	N/A	N/A
SDV80-140	135'	N/A	N/A
SDV100-199	135'	N/A	N/A
SDV100-260	N/A	135'	N/A
SDV100-400*	N/A	45'*	110'*

*The first 10 feet of exhaust vent run connected to this model must be run in CPVC or equivalent. The intake air may be all PVC.

NOTE: Each 90° elbow is equivalent to 5 feet of pipe. Two 45° elbows are equivalent to 5 feet of pipe.

Sandblaster® Force™ Sample Specifications

Gas water heater(s) shall be a State Industries, Inc. Sandblaster Force, Model Number,						1. A	-year limited warranty against failure due to corrosion, metal fatigue or overheating
____________________, with a				gallon storage capacity, an input rate of		caused by	the buildup of scale, film or other sediment.
		Btu/Hour	gas, and a recovery rate of		gallons per hour at a	2. Against electrolytic corrosion by multiple, factory-installed magnesium anodes.
	degree Fahrenheit temperature rise.
						3. Against failure due to overheating caused by the buildup of scale, film and other sediment
Unit(s) shall be direct-vent design, with an automatic blower-powered, two pipe air intake and
						by a construction which incorporates an annular ring, which fits inside the tank at the base. The
exhaust system communicating directly with the outside of the building;. The blower shall have
						ring shall be equipped with a group of calibrated jets, properly positioned so that they will direct
a safety device that will not allow the operation of the pilot and main burners unless the blower
						the flow of inlet water in such a way that microscopic particles of precipitated solids shall be
is in operation. Unit(s) shall have a combustion air passage that is internal to the outer jacket
						kept in suspension and exhausted from the water heater on that or successive hot water draws.
of the water heater other than the intake and exhaust connections at the top of the water heater.
						The burner(s) shall have an individual orifice for each burner tube and be constructed of tubular
The units shall be equipped with an Intermittent Electronic Ignition control requiring an external
120 Volt power supply with a rating of 12 amps or less. The control system shall shut off the						aluminized or stainless steel mounted in an easily removable tray.
gas supply to the unit within 4 seconds if the gas supply or pilot flame are interrupted. The tank						Water heater(s) shall have the CSA International seal of certification, a working pressure of 150 psi, a
shall be additionally protected against premature failure in the following ways:						factory-installed ASME rated temperature and pressure relief valve, and a 4˝ x 5˝ tank inspection port.

WATER HEATERS 500 Lindahl Parkway, Ashland City,TN 37015

EC/SDV1/0601 ©2001 State Industries, Inc. Printed in U.S.A.