Manuals / Brands / Kitchen Appliance / Freezer / Stoelting / Kitchen Appliance / Freezer

Stoelting Endura 111, Futura 112 REPLACEMENT PARTS, O-Ringsare drawn to Approximate Size, SECTION, Rear Seal (1), Carburetor (2), Front Door (1), 4" ID x 3/16" CS, 1-1/8"ID x 1/8" CS

1 33

Download 33 pages, 3.81 Mb

SECTION 5

REPLACEMENT PARTS

5.1 HOW TO ORDER PARTS

To assure receipt of the proper replacement parts, supply your dealer or distributor with the following informa- tion:

A. Model number of equipment.

B.Serial number of model, stamped on nameplate

C.Part number, part name and quantity needed. Com- mon part names and numbers are listed in this manual.

Part Number	Description
208401	Brush, 2.54 cm (1") diameter
208135	Brush, 10 cm (4") diameter
208381	Brush, .95 cm (3/8") diameter
208467	Brush, .80 cm (5/16") diameter
324107	Decal - Hazardous Moving Parts
324105	Decal - Electrical Shock Hazard
324106	Decal - Applicable Electrical Code
324108	Decal - Caution
324141	Decal - Caution - Rotation Blade
324584	Decal - Adequate Ventilation
368140	Air Filter
508135	Petro-Gel Lubricant
508048	Spline Lubricant
1158022	Small Parts Kit

O-RING IDENTIFICATION SHEET

MODELS ENDURA/FUTURA 111

	Carburetor (2)
	624677		Rear Seal (1)
	1-1/8" ID x 1/8" CS	Front Door (1)	Rear Seal (1)
	1-1/8" ID x 1/8" CS	Front Door (1)	624678
		625133	624678
		625133	1-1/8" ID x 3/16" CS
		4" ID x 3/16" CS	1-1/8" ID x 3/16" CS
		4" ID x 3/16" CS

Spigot (2) 624600 5/8" ID x 1/8" CS

O-Rings are drawn to Approximate Size

21

Contents

Page Page Page Page OWNER'S MANUAL FOR MODEL ENDURA 111/112 AND FUTURA 111/112 STOELTING COUNTER MODEL GRAVITY FREEZER SOFT SERVE Page SECTION DESCRIPTION PAGE 1. INTRODUCTION 2. INSTALLATION INSTRUCTIONS FIGURE TITLE DESCRIPTION AND SPECIFICATIONS MODEL ENDURA/FUTURA 111/112 COUNTER MODEL GRAVITY FREEZER DIMENSIONS: WEIGHT: SECTION INSTALLATION INSTRUCTIONS 2.1SAFETYPRECAUTIONS Do not STOELTING, INC 2.2 SHIPMENT AND TRANSIT Donot Stoelting, Inc. cannot make any claims against the carrier 2.3FREEZERINSTALLATION 2.4 FLOOR STAND INSTALLATION NOTE WARNING 2.5 INSTALLING PERMANENT WIRING DISCONNECT FREEZER FROM THE SOURCE OF ELECTRICAL SUPPLY BEFORE SERVICING Page INITIAL SETUP AND OPERATION High Pressure Cutout Switch Located Back of Freezer (Some Models) A.SPIGOT SWITCH B.OFF-ONSWITCH C.PUSH TO FREEZE SWITCH D.GREENLIGHT E.CLEAN SWITCH Figure 11. Mix Inlet Regulator Figure 12. Clean Control Figure 13. Sanitizing Hopper Figure 14. Draining Solution 3.4 FREEZEDOWNANDOPERATION Figure 15. Dispensing Product 3.5 MIX INFORMATION 3.6 REMOVING MIX FROM FREEZER Figure 16. Removing Mix Inlet Regulator Figure 17. Draining Mix 3.7 CLEANINGTHEFREEZER 3.8 DISASSEMBLY OF FREEZER PARTS Figure 18. Auger Flight Wear and Front Auger Support Bushing Wear ËHopper Cover Figure 22. Auger Shaft Removal DO NOT USE ANY TYPE OF SHARP OBJECT TO REMOVE THE "O" RINGS Figure 23. Removing "O" Ring 3.9 CLEANINGTHEFREEZERPARTS DO NOT DAMAGE PARTS BY DROPPING OR ROUGH HANDLING Figure 25. Exploded View of Auger (E111 Shown) Figure 26. Exploded View of Front Door FINGER TIGHTEN THE CIRCULAR KNOBS EVENLY. DO NOT OVERTIGHTEN KNOBS Figure 27. Mix Inlet Regulator 3.12ROUTINECLEANING 3.13PREVENTIVEMAINTENANCE A.Cleaning and Sanitizing Information Soil Materials Associated with Frozen Dessert Machines eventually defy sanitizing efforts This can lead to high bacteria counts and a food safety dilemma Additional Information THE USE OF DELIMERS PRODUCT SAFETY MACHINE DAMAGE DO NOT USE BLEACH D. MONTHLY E. SEMI-ANNUALLY 3.14EXTENDEDSTORAGE TROUBLESHOOTING CHARTS Page CODE P.T.F. LIGHT FLASHES MEANING Page REPLACEMENT PARTS O-Ringsare drawn to Approximate Size Page Page Page WARRANTY SOFT SERVE / SHAKE FREEZERS 1.Scope: 2.Disclaimer of Other Warranties: 3.Remedies: