Summit manual Absolute Maximum Ratings, S93WD462/S93WD463, Comment, Temperature

	S93WD462/S93WD463
ABSOLUTE MAXIMUM RATINGS*
Temperature Under Bias	–55°C to +125°C
Storage Temperature	–65°C to +150°C
Voltage on any Pin with Respect to Ground(1)	–2.0V to +VCC +2.0V
VCC with Respect to Ground	–2.0V to +7.0V
Package Power Dissipation Capability (Ta = 25°C)	1.0W
Lead Soldering Temperature (10 secs)	300°C
Output Short Circuit Current(2)	100 mA

*COMMENT

Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability.

RECOMMENDED OPERATING CONDITIONS

Temperature	Min	Max
Commercial	0°C	+70°C
Industrial	-40°C	+85°C
		2029 PGM T7.0
RELIABILITY CHARACTERISTICS

Symbol	Parameter	Min.	Max.	Units
NEND(3)	Endurance	100,000		Cycles/Byte
TDR(3)	Data Retention	100		Years
VZAP(3)	ESD Susceptibility	2000		Volts
ILTH(3)(4)	Latch-Up	100		mA

D.C. OPERATING CHARACTERISTICS (over recommended operating conditions unless otherwise specified)

				Limits
	Symbol	Parameter	Min.	Typ.	Max.	Units	Test Conditions
	ICC	Power Supply Current			3	mA	DI = 0.0V, fSK = 1MHz
		(Operating)					VCC = 5.0V, CS = 5.0V,
							Output Open
	ISB	Power Supply Current			50	µA	CS = 0V
		(Standby)					Reset Outputs Open
	ILI	Input Leakage Current			2	µA	VIN = 0V to VCC
	ILO	Output Leakage Current			10	µA	VOUT = 0V to VCC,
		(Including ORG pin)					CS = 0V
	VIL1	Input Low Voltage	-0.1		0.8	V	4.5V-VCC<5.5V
	VIH1	Input High Voltage	2		VCC+1	V
	VIL2	Input Low Voltage	0		VCCX0.2	V	1.8V-VCC<2.7V
	VIH2	Input High Voltage	VCCX0.7		VCC+1	V
	VOL1	Output Low Voltage			0.4	V	4.5V-VCC<5.5V
	VOH1	Output High Voltage	2.4			V	IOL = 2.1mA
							IOH = -400µA
	VOL2	Output Low Voltage			0.2	V	1.8V-VCC<2.7V
	VOH2	Output High Voltage	VCC-0.2			V	IOL = 1mA
							IOH = -100µA
							2029 PGM T3.0
Note:

(1)The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC voltage on output pins is VCC +0.5V, which may overshoot to VCC +2.0V for periods of less than 20 ns.

(2)Output shorted for no more than one second. No more than one output shorted at a time.

(3)This parameter is tested initially and after a design or process change that affects the parameter.

(4)Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1V to VCC +1V.

SUMMIT MICROELECTRONICS, Inc. 2029 2.2 1/23/01 7