Sylvania 6615LG Preparation For Use, Operations, Unpacking, Connections, Initial Setup

PREPARATION FOR USE

UNPACKING

The stand of this TV is folded when you pur- chased. Place this TV face-down on a flat sur- face covered with the soft cloth. Bend the stand slowly to forward until it clicks.

Do not bend from this side.

If you want to fold the stand again, insert a thin rod into the hole in the right side of the stand as illustrated, bend the stand backward while you keep pushing the hole.

CONNECTIONS

Plug the incoming cable into the ANT jack on the rear of the TV.

Cable		Antenna
	OR
TV signal		Rear of this TV

Incoming cable from home Antenna /

Cable Company (No Cable Box)

	Cable Box or
	Satellite Box*
OR	OUT
	IN
		ANT
		*NOTE (DO NOT DISCONNECT FROM BOX)
Incoming cable from Cable		Some cable TV systems use scrambled signals and require
Company or Satellite Antenna		a special converter to receive these channels. Consult
		your local cable company.

You can bracket this product as wall mounting TV using the arm adapted for 100mm (commercially available).

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

INITIAL SETUP

When you turn on the power for the first time, the “SELECT LANGUAGE” menu is displayed. The “INITIAL SETUP” menu is displayed every time you turn on the unit unless the scanning is completed.

1 Select the desired	SELECT LANGUAGE		2 If the TV screen shows	- HELPFUL HINTS -
language according to			snow noise and there is	1. PLEASE CHECK TO SEE IF THE
	ENGLISH	NEXT:PRESS CHK		PROPERLY CONNECTED.
the screen indication.			no operation for more	ANTENNA/CABLE/SATELLITE IS
	FRANÇAIS	APRÈS:PRESSEZ VOLX		OWNER’S MANUAL OR REAR PANEL FOR
	ESPAÑOL	DESPUÉS:PRESIONE CHL		2. DID YOU PERFORM “AUTO PRESET CH” ?
After that, the TV			than 5 seconds,	3. PLEASE REFER TO FRONT PAGE OF THE
				SUPPORT LINE INFORMATION.
performs “AUTO			“HELPFUL HINTS”
PRESET CH” to scan			appears. Follow the
channels available for		– INITIAL SETUP –	instructions listed on-
	PLEASE CONNECT ANTENNA OR CABLE
the broadcasting in	OR SATELLITE TO THIS UNIT.		screen.
	IN ORDER TO PERFORM
your area.	THEN PRESS CH K,
	“AUTO PRESET CH ”.

When the scanning is completed, or [MENU] is pressed during channel scanning to cancel it, the tuner stops on the lowest memorized channel.

Notes:

●In case no channel can be received by the channel scanning, “NO TV SIGNALS” is displayed on the screen. Turn off the unit and check the antenna connection, then follow step 1 again.

●If those settings do not work properly, please call our help line on the front page of this owner's manual.

SELECTING AUDIO/VIDEO INPUT

When you use the AUDIO/VIDEO input jacks, select “VIDEO1” or “VIDEO2” mode by pressing [INPUT SELECT] on the remote control or [SELECT] on the main unit. The input mode changes by pressing the button as following:

INPUT	TV channel	VIDEO1	VIDEO2
SELECT

TILT STAND
Tilt Stand	-5°10°
Adjust the stand to change the angle of TV (-5°~ 10°).

OPERATIONS

REMOTE CONTROL AND FRONT PANEL FUNCTION

Note:

•For your safety and to avoid damages to the unit, unplug the antenna cable from the

ANT jack before moving the unit.

IR transmitter

To send infrared ray (IR) signal

INPUT

SELECT

POWER button

INPUT SELECT button

To select TV or external input

[EXTERNAL CONNECTION]

VIDEO1 input

Rear of this TV

To turn TV on/off	POWER
VOL X/Y buttons	o CH

CH K/L buttons

To select channels and move

ex.

(OUT)

Audio Cable

(OUT)

Video Cable

(IN)

(IN)

(IN)

			R
AU	DIO
			L
VIDEO1			EO
VID
S-VI		DEO
	AN			T

	m		p
To adjust volume	VOL	n
To decide the command of settings	1	2	3
	4	5	6
	7	8	9

up/down through menu items

Channel number buttons

Press two digits to directly access the desired channel. Remember to press a "0" before a single digit channel.

+100 button

Video Cassette	OR
	(OUT)
Recorder
	S-Video Cable

	AD	PH	ON	E
HE

MENU button	MENU 0 +100
To view on-screen menu

Press to select cable channels higher than 99.

SLEEP button

Notes:

●The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for connecting monaural audio equipment.

●The S-VIDEO jack is given priority over the VIDEO jack.

MUTE button	MUTE SLEEP CH RET
To mute sound
DISPLAY button	DISPLAY
To display CH No./Audio Status

To set Sleep Timer

CH RET button

To return to previous channel

VIDEO2 input

ex.

(OUT)

Audio Cable Video Camera

(OUT)

Video Game	Component
	Video Cable

(IN)

(IN)

Rear of this TV

VIDEO2

R

AUDIO

L

COMPONENT

Y

Pb

Pr

Note:

●You can test if the remote control sends out the infrared signal with an AM radio. (Refer to “TROUBLESHOOTING GUIDE”.)

MENU button

To view on-screen menu

VOLUME X/Y buttons

To adjust volume

CHANNEL K/L buttons

To select channels

SELECT button

To select TV or external input

POWER button

Notes:

●This TV can accept 480p / 480i / simplified 1080i video signal.

●Simplified 1080 video signal differs to the original 1080i video signal because it is displayed after converted into 480p signal.

To turn TV on/off

MENU VOLUME CHANNEL SELECT POWER

INSTALLING THE BATTERIES
1	2	3	Install two AAA batteries (supplied) matching
			the polarity indicated inside battery compart-
			ment of the remote control.

[BATTERY PRECAUTIONS]

•Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device.

•Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries with fresh ones.

•If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.

•Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.

Infrared Sensor Window

Note:

●If some digits appear in the corner of the screen when the unit is turned on at the first time, press [POWER] without unplugging the power cord.