Sylvania DVR90DF owner manual Functional overview, Front Panel

Before you start

Functional overview

Front Panel 1

(*) The unit can also be turned on by pressing these buttons.

1.	Disc tray
2.	Place a disc when open.
	Display
3.	Refer to “Front Panel Display Guide” on page 12.
	OPEN/CLOSE A button*
4.	Hit to open or close the disc tray.
	CHANNEL L / K button
5.	Press to change the channel up and down.
	REV E button
	During playback, hit to skip to the previous chapter
	or track.
	During playback, press and hold for 1.5 seconds to fast reverse.
6.	When playback is paused, hit repeatedly to slow reverse.
	FWD D button
	During playback, hit to skip to the next chapter or track.
	During playback, press and hold for 1.5 seconds to
	fast forward.
7.	When playback is paused, hit repeatedly to slow forward.
	STOP C button*
8.	Hit to stop play or recording.
	PLAY B button*
	Hit to start or resume play.
Rear Panel		1 2				3
			VIDEO IN	COMPONENT
	IN			VIDEO OUTPUT		VIDEO OUT
			S-VIDEO		Y
							DIGITAL AUDIO OUTPUT
			IN	OUT
	OUT		L			L	PCM / BITSTREAM
					PB/CB
			R			R
	ANTENNA AUDIO IN				PR/CR	AUDIO OUT	COAXIAL
			(L1)
	11		10 9	8 7		6	5
1. ANTENNA IN jack
	Use to connect an antenna.
2. VIDEO IN jack (LINE1)
	Use to connect external equipment with a standard video cable.
3. VIDEO OUT jack
	Use to connect a TV monitor, AV receiver or other

equipment with a standard video cable.

4. AC Power Cord

Connect to a standard AC outlet to supply power to this unit.

5. COAXIAL DIGITAL AUDIO OUTPUT jack Use to connect an AV receiver, Dolby Digital decoder or other equipment with a coaxial digital input jack with a digital coaxial cable.

6. AUDIO OUT jacks

Use to connect a TV monitor, AV receiver or other equipment with standard audio cables.

2	3* 4	5 6 7* 8* 9
	OPEN/CLOSE CHANNEL	REV FWD	STOP	PLAY	POWER
	REC SPEED REC/OTR
		S-VIDEO	VIDEO	L	AUDIO R

15	14 13	1211 10
9.	POWER button
	Hit to turn the unit on and off.

If timer programmings have been set, hit to set the unit in timer-standby mode.

10. AUDIO input jacks (LINE2)

Use to connect external equipment with standard audio cables.

11. VIDEO input jack (LINE2)

Use to connect external equipment with a standard video cable.

12. S-VIDEO input jack (LINE2)

Use to connect the S-Video output of external equip- ment with an S-Video cable.

13. REC/OTR button

Hit once to start a recording. Hit repeatedly to start

aone-touch Timer Recording.

14. REC SPEED button

Hit to switch the recording speed.

15. Remote control sensor

Receive signals from your remote control so that you can control the unit from a distance.

4

7. COMPONENT VIDEO OUTPUT jacks

Use to connect a TV monitor with component video inputs with component video cables.

8. S-VIDEO OUT jack

Use to connect the S-Video input of a TV monitor, AV receiver or other equipment with an S-Video cable.

9. S-VIDEO IN jack (LINE1)

Use to connect the S-Video output of external equip- ment with an S-Video cable.

10. AUDIO IN jacks (LINE1)

Use to connect external equipment with standard audio cables.

11. ANTENNA OUT jack

Use to connect an antenna cable to pass the signal from the TV ANTENNA IN to your TV monitor.

Note

•Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit.

•This unit does not have the RF modulator.

8