TO SELECT A DESIRED CHANNEL
You can select the desired channel by using the CHANNEL K or L button on or directly pressing the number buttons on the remote control.
Note for using the number buttons:
• When selecting cable channels which are higher |
than 99, press the +100 button first, then, press the |
1Select “SETTING CLOCK”
Press the MENU button on the remote control.
Press the PLAY/K or STOP/L but- ton to point to “SETTING CLOCK”.
Then, press the F.FWD/B button.
– M E N U –
TIMER PROGRAMMING PICTURE CONTROL
BSETTING CLOCK CHANNEL SET UP USER’S SET UP
TIME SEARCH
last two digits. (Example: to select channel 125, |
first press the +100 button then press “2” and “5”). |
• You must proceed |
with a zero (Example: 02 ... 09). |
CLOCK SET UP
(AUTO / MANUAL)
Set the clock accurately for proper automatic timer recording. If the Public Broadcasting Station (PBS) is available in your area, follow “AUTO CLOCK SETTING”. If it is not, follow “MANUAL CLOCK SETTING”.
AUTO CLOCK SETTING
You can have the TV/VCR set the clock automatical- ly by using the Public Broadcasting Station (PBS) channel in your area. Once you have set the clock by using the following procedure, the TV/VCR will automatically monitor the correct time and date being broadcast by the PBS station in your area, using a new service called Extended Data Service (XDS).
2 Set “AUTO CLOCK” to [ON] | – SETTING CLOCK – | |
Press the F.FWD/B or REW/s | B AUTO CLOCK | [ON] |
button repeatedly until [ON] | AUTO CLOCK CH | [AUTO] |
|
| |
appears. | MANUAL CLOCK SET |
|
| D.S.T. | [OFF] |
3Enter the channel number for the PBS station
Press the PLAY/K or STOP/L button to point to
“AUTO CLOCK CH”.
– SETTING CLOCK –
Then press the F.FWD/B or
REW/s button until the channel | AUTO CLOCK | [ON] |
B AUTO CLOCK CH | [AUTO] | |
number for your local PBS station | MANUAL CLOCK SET |
|
appears. |
| |
D.S.T. | [OFF] |
If you do not know the PBS channel
number, leave it set to [AUTO] which is located before [2]. The TV/VCR will search automatically all available channels for the local PBS station, and will select that channel.
4Exit the Auto Clock Setting
Press the MENU button on the remote control to return to TV mode.
Make sure ...
•TV/VCR power must be turned on.
•Confirm that the antenna connections are correct.
•The cable converter box must be turned on if your TV/VCR is connected directly to it. (See NOTES:)
•The channel is properly set in advance.
NOTES:
•Auto clock setting only needs to be set once. But it can be done again if the clock’s time has become incorrect for some reason.
•If the TV/VCR is connected directly to a cable converter box or satellite box, the local PBS station must be selected on the cable box itself, and the TV/VCR must be set to the output channel of the cable converter box or satellite box (usually chan- nel 3 or 4), to be able to set up or correct the clock automatically.
If you do not know what your local PBS station is, then follow “MANUAL CLOCK SETTINGS”. The TV/VCR cannot control the channels of the cable converter box or satellite box.
5Turn off the TV/VCR
Turn the TV/VCR off. Because the Auto Clock func- tions automatically while the TV/VCR is off.
If you choose [AUTO],
•The TV/VCR must search until the PBS channel is found. It must scan each channel for a couple of seconds to determine if that channel is transmitting the XDS signal.
•If the time, that is automatically set by this select- ed PBS station is incorrect, it may not be your local PBS station, but one from a different time zone. Or there is a case that no channel is broad- casting the XDS signal in your area, as shown by no time. In these cases, you must manually enter the correct local PBS station, or set the clock man- ually and turn off the Auto Clock Setting feature.
MANUAL CLOCK SETTING
Make sure ...
•TV/VCR power must be turned on.
In the example below, the clock is to be set to:
DATE | May 7th, 2002 |
SETTING TIME | 5:40PM |
- 11 - | EN |
