Symbol Technologies LS 400XI

5-17

Parameter Menus

Transmit “No Read” Message

Scan a bar code below to select whether or not a “No Read” message is transmitted. When

enabled, if a symbol does not decode, “NR” is transmitted. Any preﬁxes or sufﬁxes which

have been enabled are appended around this message. When disabled, if a symbol does not

read, nothing is sent to the host.

ENABLE NO READ

DISABLE NO READ

Contents

Main i Contents ii Chapter 4. Maintenance & Specifications Chapter 5. Parameter Menus iii iv Appendix A. Programming Reference Index Feedback About This Manual Service Information Related Publications Notational Conventions Symbol Support Center Chapter 1 The LS 400Xi Scanner Scanning Made Easy Page Chapter 2 Set Up Page Switching Cables Power Options Battery Box Operation Connecting to a Host - 1D Scanning Direct RS-232 RS-232C (LS 4004i) RS-232 via Synapse Battery Operation External Power Operation with Single-Piece Cable Keyboard Wedge IBM 468X/9X (LS 4005i) Page Page Connection to a Host - PDF Scanning Chapter 3 Scanning Scanning 1-D Bar Codes Aiming Scan the Entire Symbol Hold at an Angle Scanning PDF417 (2-D) Bar Codes What If... Nothing happens when you follow the operating instructions? Symbol is decoded, but not transmitted to the host terminal? Scanned data is incorrectly displayed on the terminal? Chapter 4 Maintenance & Specications Maintenance Accessories Required Accessories Optional Accessories Technical Specications Table 4-1. Technical Specications 4-3 Table 4-1. Technical Specications (Contd) Page LS 400Xi 2-D Decode Zone 4-6 Pin-outs Table 4-2. Pin-outs 4-7 Beeper Indications Table 4-3. Beeper Indications Page Chapter 5 Parameter Menus Operational Parameters 5-2 5-3 5-4 5-5 5-6 Page Host T ype IBM 46XX Host Types 5-9 RS-232C Host Types Page RS-232C Host Types (Contd) Page Page Laser On Time Page Page Page Page Linear Code Type Security Level Linear Security Level 1 Linear Security Level 2 Page Page Enable/Disable UPC-E/UPC-A/UPC-E1 Page Page Decode UPC/EAN Supplementals Decode UPC/EAN Supplemental Redundancy Transmit UPC-A/UPC-E/UPC-E1 Check Digit UPC-A Preamble UPC-E Preamble UPC-E1 Preamble Convert UPC-E to UPC-A Convert UPC-E1 to UPC-A Page Page UPC/EAN Security Level UPC/EAN Security Level 0 UPC/EAN Security Level 1 Page Page Page Page Page Enable/Disable Trioptic Code 39 Page Page Set Lengths for Code 39 Set Lengths for Code 39 (Contd) Page Page Enable/Disable Code 39 Full ASCII Code 39 Buffering (Scan & Store) Buffer Data Clear Transmission Buffer Transmit Buffer Overlling Transmission Buffer Attempt to Transmit an Empty Buffer Page Set Lengths for Code 93 Set Lengths for Code 93 (Contd) Page Set Lengths for Interleaved 2 of 5 Set Lengths for Interleaved 2 of 5 (Contd) Page Page Convert I 2 of 5 to EAN-13 Page Set Lengths for Discrete 2 of 5 Set Lengths for Discrete 2 of 5 (Contd) Page Set Lengths for Codabar Set Lengths for Codabar (Contd) Page Page Page Set Lengths for MSI Plessey Set Lengths for MSI Plessey (Contd) Page Page Page Page Transmit Code ID Character Symbol Code ID Characters Page Page Prex/Sufx Values Scan Data Transmission Format Page RS-232C Parameters Baud Rate Page Parity Page Hardware Handshaking Page Hardware Handshaking (Contd) RTS/CTS Option 3 Software Handshaking None ACK/NAK Software Handshaking (Contd) ENQ ACK/NAK with ENQ XON/XOFF Host Serial Response Time-out RTS Line State Stop Bit Select ASCII Format Beep on <BEL> Intercharacter Delay Numeric Bar Codes Page Page Appendix A Programming Reference UCC/EAN-128 A-2 Table A-1. Reading Standard Code128 & UCC/EAN 128 AIM Code Identiers A-4 A-5 Table A-3. Modier Characters (Contd) Index-1 Index A B Index-2 C D I M N Tell Us What You Think...