Symbol Technologies PDT 8100 - page 34

32

PDT 8100 Series

with Windows Mobile

2003 for Pocket PCs

When receiving

beamed data an

out of memory

message ap-

pears.

Not enough free

memory available

for receiving data.

Your terminal requires at least

twice the amount of memory avail-

able as the data you are receiving.

For example, if you are receiving a

30K application, you must have at

least 60K free.

Your terminal

does not accept

scan input.

Scanning applica-

tion is not loaded. Verify that the unit is loaded with a

scanning application. See your

System Administrator.

Unreadable bar

code. Be sure the symbol is not defaced.

Distance be-

tween exit window

and bar code is in-

correct.

Be sure you are within proper

scanning range.

Terminal is not

programmed for

the bar code.

Be sure the terminal is pro-

grammed to accept the type of bar

code you are scanning.

Terminal is not

programmed to

generate a beep.

If you are expecting a beep on a

good decode and don’t hear one,

check that the application is set to

generate a beep on good decode.

Battery is low. If the scanner stops emitting a la-

ser beam when you press the trig-

ger, check your battery level.

Note: If the scanner is still not

reading symbols, contact your dis-

tributor or Symbol Technologies.

Problem Cause Solution

6598801a.fm Page 32 Monday, December 8, 2003 2:01 PM

Contents

Main PDT 8100 Series with Windows Mobile 2003 for Pocket PCs Introduction About This Guide Accessories Parts of the Terminal 6598801a.fm Page 3 Monday, December 8, 2003 2:01 PM Parts of the Terminal (continued) 6598801a.fm Page 4 Monday, December 8, 2003 2:01 PM Getting Started Inserting a Compact Flash Card Removing a Compact Flash Card Installing the 1950 mAh Battery Charging the Battery 9 Charging the Battery Using the Serial/Charging Cable 15-Pin Serial Port Connector Attaching the Trigger Handle (Quick Grip compatible terminals only) 10 Attaching the Handstrap Starting the Terminal 1 2 3 Aligning the Screen Initiating a Network Connection Controlling the Backlight 12 Adjusting the Backlight Using a Headset 13 Using the Keyboard Using the 28-Key Keyboard Page 15 Using the 37-Key Keyboard Page 17 Using the 47-Key Keyboard PDT 8100 Series with Windows Mobile 2003 for Pocket PCs Using the Stylus Today Screen Navigation Bar and Command Bar Input Methods Using the Soft Keyboard Using the Block Recognizer Using the Letter Recognizer Using the Transcriber Block Recognizer Characters Scanning Capturing Still Images 25 Resetting Your Terminal Performing a Soft Reset Performing a Hard Reset 26 Host Communications Using the RS-232 Serial Cable 27 Using the Cradle Communicating with Printers Maintaining the Terminal PDT 8100 Series with Windows Mobile Troubleshooting Page Page Page Page Terminals with an integrated imager: End-user License Agreement 6598801a.fm Page 34 Monday, December 8, 2003 2:01 PM APPROVED ADDITIONAL TEXT IF THE DEVICE IS LEASED 6598801a.fm Page 35 Monday, December 8, 2003 2:01 PM UPGRADES AND RECOVERY MEDIA. 6598801a.fm Page 36 Monday, December 8, 2003 2:01 PM 37 Battery Information Health and Safety Recommendations Ergonomic Recommendations Regulatory Information 38 PDT 8100 Series with Windows Mobile Radio Modules FCC RF Exposure Guidelines Laser Devices Page 40 6598801a.fm Page 40 Monday, December 8, 2003 2:01 PM Laser Labels Power Supply 41 Cell Phone/Terminal Warnings Page 43 Hearing Aid Compatibility Radio Frequency Interference Requirements-FCC Radio Frequency Interference Requirements - Canada 44 Marking and European Economic Area (EEA) Statement of Compliance Other Countries Warranty 6598801a.fm Page 45 Monday, December 8, 2003 2:01 PM Service Information