PREPARATION FOR USE
CONNECTIONS
You can enter into Video mode from Game mode by adjusting a Picture control.
Plug the incoming cable into the ANT. IN jack on the rear of the TV.
Cable | OR | Antenna | Rear of this TV |
| |||
TV signal |
|
| |
|
|
|
Incoming cable from home Antenna /
Cable Company (No Cable Box)
Cable Box or |
|
Satellite Box* |
|
OR |
|
OUT | ANT. IN |
IN | |
Incoming cable from Cable | *Note (DO NOT DISCONNECT FROM BOX) |
Company or Satellite Antenna | |
Cables not included | Some cable TV systems use scrambled signals and |
require a special converter to receive these channels. | |
| Consult your local cable company. |
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
1To use external input
GAME
GAME
Picture: GAME (ON)
Input: External
2To cancel Game mode only
MENU
VOL | GAME MODE [+] | ||
OFF | ON | ||
| |||
Select “PICTURE” |
|
| |
After 10 seconds |
| VIDEO | |
|
|
Picture: Customized
Input: External
3To return to TV channel
15
GAME
2 times
Note:
•For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. IN jack before moving the unit.
[EXTERNAL CONNECTION]
OPERATIONS
REMOTE CONTROL AND FRONT PANEL FUNCTION
IR transmitter
Front AUDIO/VIDEO input
ex.
Front of this TV
VIDEO AUDIO
To send infrared ray (IR) signal
POWER button
POWER | GAME SLEEP |
GAME button
Press to set the Game mode
Video Cable
To turn TV on/off
SLEEP button
(OUT)(IN)
(OUT) | (IN) |
Channel number buttons
Press two digits to directly access the desired channel. Remember to press
1 2 3
4 5 6
7 8 9
DISPLAY
CHANNEL
RETURN
To set Sleep Timer
DISPLAY button
To display CH No./Audio Status
Video Camera | Video Game | Audio Cable |
INSTALLING THE BATTERIES |
| ||
1 | 2 | 3 | Install two AA batteries (supplied) |
|
|
| matching the polarity indicated inside |
|
|
| battery compartment of the remote con- |
|
|
| trol. |
[BATTERY PRECAUTIONS]
• Be sure to follow the correct polarity as indicated in the battery compartment. |
a "0" before a single digit channel.
CH(ANNEL) K / L buttons
To select channels and move up/down through menu items
MENU button To view
0 +100
| CH |
VOL | VOL |
| CH |
| MUTE |
MENU
CHANNEL RETURN button
To return previous screen
MUTE button
To mute sound
VOL(UME) K / L buttons To adjust volume
To decide the command of settings
Reversed batteries may cause damage to the device. |
• Do not mix different types of batteries together (e.g. Alkaline and |
with fresh ones. |
• If the device is not to be used for a long period of time, remove the batteries to prevent |
damage or injury from possible battery leakage. |
• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. |
INITIAL SETUP
When you turn on the power for the first time, the “SELECT LANGUAGE” menu is displayed. The “INITIAL SETUP” menu is displayed every time you turn on the unit unless the scanning is completed.
1 Select the desired | SELECT LANGUAGE |
| 2 If the TV screen shows | - HELPFUL HINTS - |
language according to |
| snow noise and there | 1. PLEASE CHECK TO SEE IF | |
ENGLISH |
| SATELLITE IS PROPERLY | ||
|
|
|
| THE ANTENNA/CABLE/ |
the screen indication. | NEXT:PRESS CHK |
| is no operation for | CONNECTED. |
ESPAÑOL |
| 2. DID YOU PERFORM | ||
After that, the TV |
| more than 10 seconds, | “AUTO PRESET CH” ? | |
DESPUÉS:PRESIONE CHL |
| PAGE OF THE OWNER’S | ||
|
|
| 3. PLEASE REFER TO FRONT | |
performs “AUTO | FRANÇAIS |
| “HELPFUL HINTS” | MANUAL OR REAR PANEL |
APRÈS:PRESSEZ VOLK |
| FOR SUPPORT LINE | ||
PRESET CH” to scan |
|
| appears. Follow the | INFORMATION. |
|
|
| ||
channels available for | – INITIAL SETUP – |
| instructions listed on |
|
the broadcasting in | PLEASE CONNECT ANTENNA |
| the screen. |
|
OR CABLE OR SATELLITE |
|
| ||
your area. | TO THIS UNIT. |
|
|
|
THEN PRESS CH K, |
|
|
| |
|
|
|
| |
| IN ORDER TO PERFORM |
|
|
|
| “AUTO PRESET CH”. |
|
|
|
|
|
|
|
|
When the scanning is completed, or [MENU] is pressed during channel scanning to cancel it, the tuner stops on the lowest memorized channel.
Notes:
●In case no channel can be received by the channel scanning, “NO TV SIGNALS” is displayed on the screen. Turn off the unit and check the antenna connection, then follow step 1 again.
●If those settings do not work properly, please call our help line on the front page of this owner's manual.
SELECTING AUDIO/VIDEO INPUT
You can select external input jacks by pressing [GAME] on the remote control.
1 To use external input | 2 To return to TV channel |
GAME | 15 |
GAME | GAME |
Picture: GAME (ON)
Input: External
In the Game mode, you can use front input jacks with suitable picture adjustments for video games.
Notes:
●If you press [GAME] when the TV is off, the TV turns on and enters in Game mode.
●If you adjust another picture control while in Game mode, this mode will automatically
be canceled.
Note:
●You can test if the remote control sends out the infrared signal with an AM radio. (Refer to “TROUBLESHOOTING GUIDE”.)
VIDEO AUDIO EARPHONE MENU | VOLUME | CHANNEL | POWER |
Infrared Sensor Window
POWER button
To turn TV on/off
CHANNEL ▲ /▼ buttons
To select channels
VOLUME X/Y buttons
To adjust volume
MENU button
To view
EARPHONE jack
AUDIO input jack
VIDEO input jack
Note:
●If some digits appear in the corner of the screen when the unit is turned on for the first time, press [POWER] without unplugging the power cord.
