Symphonic WF20L6 owner manual Preparation for USE, Operations

PREPARATION FOR USE

UNPACKING

The stand of this TV is folded when you pur- chased. Place this TV face-down on a flat sur- face covered with the soft cloth. Bend the stand slowly to forward until it clicks.

Do not bend from this side.

If you want to fold the stand again, insert a thin rod into the hole in the right side of the stand as illustrated, bend the stand backward while you keep pushing the hole.

CONNECTIONS

Plug the incoming cable into the ANT jack on the rear of the TV.

Cable		Antenna	Rear of this TV
	OR
TV signal

Incoming cable from home Antenna /

Cable Company (No Cable Box)

	Cable Box or
	Satellite Box*
OR	OUT
	IN
	ANT

Incoming cable from Cable	*NOTE (DO NOT DISCONNECT FROM BOX)
Company or Satellite Antenna	Some cable TV systems use scrambled signals
Cables not included	and require a special converter to receive these
	channels. Consult your local cable company.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

Note:

•For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT jack before moving the unit.

[EXTERNAL CONNECTION]

INITIAL SETUP

When you turn on the power for the first time, the “SELECT LANGUAGE” menu is displayed.

The “INITIAL SETUP” menu is displayed every time you turn on the unit unless the scanning is completed.

1 Select the desired	SELECT LANGUAGE		2 If the TV screen shows	- HELPFUL HINTS -
language according to			snow noise and there is	1. PLEASE CHECK TO SEE IF THE
	ENGLISH	NEXT:PRESS CHK		PROPERLY CONNECTED.
				ANTENNA/CABLE/SATELLITE IS
the screen indication.	ESPAÑOL	DESPUÉS:PRESIONE CHL	no operation for more	2. DID YOU PERFORM “AUTO PRESET CH” ?
	FRANÇAIS	APRÈS:PRESSEZ VOLX		OWNER’S MANUAL OR REAR PANEL FOR
After that, the TV			than 5 seconds,	3. PLEASE REFER TO FRONT PAGE OF THE
				SUPPORT LINE INFORMATION.
performs “AUTO			“HELPFUL HINTS”
PRESET CH” to scan		– INITIAL SETUP –	appears. Follow the
channels available for			instructions listed on-
	PLEASE CONNECT ANTENNA OR CABLE
the broadcasting in	OR SATELLITE TO THIS UNIT.		screen.
	IN ORDER TO PERFORM
	THEN PRESS CH K,
your area.	“AUTO PRESET CH ”.

When the scanning is completed, or [MENU] is pressed during channel scanning to cancel it, the tuner stops on the lowest memorized channel.

Notes:

●In case no channel can be received by the channel scanning, “NO TV SIGNALS” is displayed on the screen. Turn off the unit and check the antenna connection, then follow step 1 again.

●If those settings do not work properly, please call our help line on the front page of this owner's manual.

SELECTING AUDIO/VIDEO INPUT

When you use the AUDIO/VIDEO input jacks, select “VIDEO1” or “VIDEO2” mode by pressing [INPUT SELECT] on the remote control or [SELECT] on the main unit. The input mode changes by pressing the button as following:

INPUT	TV channel	VIDEO1	VIDEO2
SELECT

TILT STAND
Tilt Stand	-5°10°
Adjust the stand to change the angle of TV (-5°~ 10°).

OPERATIONS

REMOTE CONTROL AND TOP PANEL FUNCTION

IR transmitter

To send infrared ray (IR) signal

VIDEO1 input

ex.	(OUT)
	Audio Cable
	(OUT)
Video Cassette	Video Cable	OR
	(OUT)

Recorder S-Video Cable

HEADPHONE jack

ex.

(OUT)

(IN)

(IN)

(IN)

(IN)

Rear of this TV

					R
	AU		DIO
					L
VIDEO1					EO
		VID
		S-VI		DEO
			AN			T
	AD	PH		ON		E
HE

			INPUT
			SELECT
POWER button
To turn TV on/off	POWER
VOL X/Y buttons		o	CH
	m		p
To adjust volume	VOL	n
To decide the command of settings	1	2	3
	4	5	6
	7	8	9

INPUT SELECT button

To select TV or external input

CH K/L buttons

To select channels and move up/down through menu items

Channel number buttons

Press two digits to directly access the desired channel. Remember to press a "0" before a single digit channel.

+100 button

Press to select cable channels

Headphone

Notes:

●The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for connecting monaural audio equipment.

●The S-VIDEO jack is given priority over the VIDEO jack.

MENU button	MENU	0	+100
To view on-screen menu
MUTE button	MUTE	SLEEP	CH RET
To mute sound
DISPLAY button		DISPLAY
To display CH No./Audio Status

higher than 99.

SLEEP button

To set Sleep Timer

CH RET button

To return to previous channel

VIDEO2 input

ex.

	(OUT)
	Audio Cable
Video Camera
	(OUT)
	Component
Video Game	Video Cable

(IN)

(IN)

Rear of this TV

VIDEO2

R

AUDIO

L

COMPONENT

Y

Pb

Pr

Note:

●You can test if the remote control sends out the infrared signal with an AM radio. (Refer to “TROUBLESHOOTING GUIDE”.)

MENU button

To view on-screen menu

VOLUME X/Y buttons

To adjust volume

CHANNEL K/L buttons

To select channels

SELECT button

Notes:

●This TV can accept 480p / 480i / simplified 1080i video signal.

●Simplified 1080 video signal differs to the original 1080i video signal because it is displayed after converted into 480p signal.

INSTALLING THE BATTERIES
1	2	3	Install two AAA batteries (supplied)
			matching the polarity indicated inside
			battery compartment of the remote
			control.

[BATTERY PRECAUTIONS]

•Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device.

•Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries with fresh ones.

•If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.

•Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.

To select TV or external input

POWER button

To turn TV on/off

MENU VOLUME CHANNEL SELECT POWER

Infrared Sensor Window

Note:

●If some digits appear in the corner of the screen when the unit is turned on at the first time, press [POWER] without unplugging the power cord.