TCS-3401

Owner’s Manual

 

 

 

FELLING

Felling is more than cutting down a tree. You must also bring it down as near to an intended place as possible without damaging the tree or anything else.

Before felling a tree, carefully consider all conditions which may effect the intended direction, such as:

Angle of the tree. Shape of the crown. Snow load on the crown. Wind conditions. Obstacles within tree range (e.g., other trees, power lines, roads, buildings, etc.).

WARNING!

Always observe the general conditions of the tree. Look for decay and rot in the trunk which will make it more likely to snap and start to fall before you expect it.

Look for dry branches, which may break and hit you when you are working. Always keep animals and people at least twice the tree length away while felling. Clear away shrubs and branches from around the tree.

Prepare a path of retreat away from the felling direction.

BASIC RULES FOR FELLING TREES

Normally the felling consists of two main cutting operations-notching and making the felling cut.

Start making the upper notch cut on the side of the tree facing the feeling direction. Look through the kerf as you saw the lower cut so you do not saw too deep into the trunk.

The notch should be deep enough to create a hinge of sufficient width and strength.

The notch opening should be wide enough to direct the fall of the tree as long as possible.

Saw the felling cut from the other side of the tree between one and two inches (3-5 cm) above the edge of the notch. (Fig. 2-7D)

Never saw completely through the trunk. Always leave a hinge.

The hinge guides the tree. If the trunk is completely cut through, you lose control over the felling direction.

Insert a wedge or a felling lever in the cut well before the tree becomes unstable and starts to move. This will prevent the guide bar from binding in the felling cut if you have misjudged the falling direction. Make sure no people have come into the range of the falling tree before you push it over,

FELLING CUT, TRUNK DIAMETER MORE THAN TWICE GUIDE BAR LENGTH

Cut a large, wide notch. Then cut a recess into the center of the notch. Always leave a hinge on both sides of the center cut. (Fig. 2-7E)

Complete the felling cut by sawing around the trunk as in the Fig. 2-7F.

WARNING!

These methods are extremely dangerous because they involve the use of the nose of guide bar and can result in kickback. Only properly trained professionals should attempt these techniques.

www.tanakapowerequipment.com

9

custsvc@tanaka-ism.com

Page 9 Page 11
Page 10
Image 10
Tanaka TCS-3401 manual Basic Rules for Felling Trees
Page 9 Page 11

TCS-3401 specifications

The Tanaka TCS-3401 is a powerful and versatile tool in the world of outdoor power equipment. Designed for both residential and commercial use, this 34cc straight shaft trimmer stands out for its reliability, performance, and user-friendly features. The TCS-3401 is ideally suited for all trimming and edging tasks, helping users achieve pristine gardens and landscapes effortlessly.

One of the key features of the Tanaka TCS-3401 is its robust commercial-grade engine. The 34cc two-stroke engine offers an impressive power-to-weight ratio, delivering exceptional performance without compromising maneuverability. This engine is not only powerful but also designed for fuel efficiency, ensuring that users can get more work done on a single tank of fuel. Coupled with a high-performance air filtration system, the engine maintains optimal performance even in dusty conditions, extending its longevity.

Another hallmark of the TCS-3401 is its ergonomic design. The trimmer is equipped with a comfortable handle that reduces vibrations, allowing users to operate it for extended periods without fatigue. The adjustable handle further enhances user comfort, enabling individuals of varying heights to find the perfect operating position. This feature, along with its lightweight construction, makes the Tanaka TCS-3401 one of the most user-friendly trimmers available.

The trimmer also incorporates advanced technologies, such as the easy-start system, which reduces the effort required to start the engine. This ensures that users can get to work quickly without the frustration often associated with starting two-stroke engines. Additionally, the TCS-3401 features a sturdy and durable cutting head, capable of accommodating various attachments like blades and different types of trimmer line, making it adaptable to a wide range of tasks.

Moreover, the TCS-3401 adheres to stringent emission standards, contributing to a cleaner environment. This is especially important for users in urban areas or those who prioritize sustainability in their outdoor maintenance activities.

In sum, the Tanaka TCS-3401 is a well-engineered trimmer that combines power, durability, and comfort. Its advanced features and thoughtful design cater to the needs of both casual users and landscaping professionals, making it a reliable choice for anyone looking to maintain their outdoor spaces efficiently. Whether tackling tall grass, weeds, or creating defined edges along pathways, the TCS-3401 proves to be an invaluable tool for achieving impressive results.
Top Page Image Contents