Xhistory, Xhistory ?, Examples xhistory call

TANDBERG Video Portal

Data port Command Interface User Guide

Xhistory

"xfeedback register status/call" - to monitor call changes "xfeedback register status/call--" - to monitor only call state changes "xfeedback register configuration" - to monitor all configuration changes

The special command xhistory presents the status of the last 255 calls, made to or from the Video Portal,via a cyclic buffer mechanism.

NOTE! If the Video Portal is registered with a Video Portal, the call history can only be shown on the respective Video Portal.

xhistory ?

usage: xhistory call [1 .. 255]

Examples: xhistory call 1

*l Call 1 (type=Vtlph, protocol=H323, direction=Incoming): LogTag: 1

GatewayCallLogTag: 0

RemoteNumber: "9047123456789"

Q931Rate: 64

DisconnectCauseValue: 16

Duration: 67 *l/end

D1392602

Page 33

Image 33

TANDBERG D1392602 manual Xhistory, xhistory ?, Examples xhistory call

Contents

D1392602 Software version VTANDBERG Video Portal Data port Command Interface User Guide Data port Command Interface User Guide 3. CONNECTING TO THE DATA PORT COMMAND INTERFACE USING TELNET Table of Contents4. THE TANDBERG VIDEO PORTAL COMMANDS Command format 1. Introduction 2.1. Hardware and Cabling 2.2. TroubleshootingTANDBERG V IDEO P ORTAL DCE, 9 pin If communication cannot be established between the PC/terminal and the TANDBERG Video Portal’s Data port the following should be checked 3. Connecting to the Data port Command Interface using Telnet 4.1.1. Command format 4. The TANDBERG Video Portal CommandsNOTE! The Data port Command Interface is not case sensitive 4.1.2. Command types 4.2. The commands Xconf telnet mode onXconf telnet mode Command alplan 4.2.1. System Configuration CommandsDialplan Entry 1..64 Enabled On/Off Dialplan Entry 1..64 Name S 0 Dialplan Entry 1..64 ServiceId distinguished c xConfiguration Dialplan Entry 1 Prefix c xConfiguration Dialplan Entry 2 Property 2 Name avmode c xConfiguration Dialplan Entry 4 Prefix NOTE! The Video Portal needs to reboot before the changes will apply Ethernet H323CallSetup H323GatekeeperH323CallSetup Mode Direct/Gatekeeper H323Gatekeeper Authentication Mode Auto/Off or c xConfiguration H323Gatekeeper Authentication Mode Off Xconf H323Gatekeeper Authenticationc xConfiguration H323Gatekeeper Authentication ID NOTE! Changes become effective after reboot c xConfiguration IP Address Loadlimit Services SessionServices Service 1..64 Enabled On/Off Services Service 1..64 Name S 0 Services Service 1..64 ServiceFile S 0 c xConfiguration SIP Mode On SIP Interface Transport Default TCP/UDP/TLSc xConfiguration SIP Interface Server Address c xConfiguration SIP Interface Server Type Auto c xConfiguration SNMP SystemLocation c xConfiguration SNMP SystemContactc xConfiguration SNMP HostIPAddr 1 c xConfiguration SNMP HostIPAddr 2 c xConfiguration SNMP HostIPAddr 3 Command ExternalManager NTP Options 4.2.2. General Video Portal Commandsc xConfiguration ExternalManager Address c xConfiguration Options 1 Key 115201SS7-1-55C3EBB7 Command Dialplan Disk 4.2.3. System Status CommandsExample Disk Ethernet Ethernet ExternalManager Feedback 1MacAddress Speed MacAddress 000E0C5CB57D Speed 100full *s/end H323Gatekeeper H323Gatekeeper IPStatus Address Port Address Port 1719 *s/end NTP Options Address Port Last Update Last CorrectionName Address SubnetMask Gateway 10.31.0.1 DNS Server Service Service SystemLoad SystemUnitOptions SystemLoad Configuration Telephony VideoTelephony Hardware Version EP Configuration Telephony VideoTelephonyProductType Uptime Software Version Name ReleaseDate PRI TemperatureCelcius TemperatureFahrenheit 4.2.5. Special Xcommand Commands 4.2.4. Debug CommandsCommand Syslog Level Mask Volume CheckDisk ClearDialplanEntries ClearServiceEntries DefaultValuesSet DefaultValuesSet Level 1Example restore all default factory setting xCommand DefaultValuesSet Parameters Dial DialplanEntryDelete DialplanEntrySwap DisconnectCallOK Result parameter Session ID S 1 Example Parameter DialplanEntryNumber Example ID 1 ERROR Result parameters OK Result parameters ID 1 ERROR Result parametersEraseDisk FeedbackDeregister FeedbackRegister Expression 1 .. 15 S 0, 256 XPath expression OK Result parameters ServiceEntryDelete OptionKeyAdd OptionKeyDelete RestoreDefaultServicesExample Delete Option Key nr. 1 xCommand OptionKeyDelete Parameters ServiceEntryNumberr Example Delete Service nr. 10 xCommand ServiceEntryDelete ServiceEntrySwapParameters ServiceEntryNumberr ServiceEntryNumber2r Example Swap Service nr. 10 About Help or ? Licence Relkey Xfeedback General User Commandshelp License Xhistory xhistory ?Examples xhistory call