TANDBERG D1392602 instruction

TANDBERG Video Portal

Data port Command Interface User Guide

3.Connecting to the Data port Command Interface using Telnet

The TANDBERG Video Portal has one LAN port.

The Video Portal’s Telnet server provides access to the Data port Command Interface through a 10/100 base T network interface supporting the TCP/IP protocol.

When connected to the Video Portal, type tsh to start a t-shell from the command line. The Telnet client will receive a welcome message similar to the following:

Welcome to <System Name>

TANDBERG Video Portal Release V3.0

SW Release Date: 2007-03-13

NOTE! If the TANDBERG Video Portal has been protected with an IP password you will be prompted to enter this password before you can access the Data port Command Interface via Telnet.

D1392602

Page 6

Image 6

TANDBERG D1392602 manual Connecting to the Data port Command Interface using Telnet

Contents

TANDBERG Video Portal Data port Command Interface User Guide Software version VD1392602 Data port Command Interface User Guide 4. THE TANDBERG VIDEO PORTAL COMMANDS Table of Contents3. CONNECTING TO THE DATA PORT COMMAND INTERFACE USING TELNET Command format 1. Introduction TANDBERG V IDEO P ORTAL 2.2. Troubleshooting2.1. Hardware and Cabling DCE, 9 pin If communication cannot be established between the PC/terminal and the TANDBERG Video Portal’s Data port the following should be checked 3. Connecting to the Data port Command Interface using Telnet NOTE! The Data port Command Interface is not case sensitive 4. The TANDBERG Video Portal Commands4.1.1. Command format 4.1.2. Command types 4.2. The commands Xconf telnet mode onXconf telnet mode Dialplan Entry 1..64 Enabled On/Off Dialplan Entry 1..64 Name S 0 4.2.1. System Configuration CommandsCommand alplan Dialplan Entry 1..64 ServiceId distinguished c xConfiguration Dialplan Entry 1 Prefix c xConfiguration Dialplan Entry 2 Property 2 Name avmode c xConfiguration Dialplan Entry 4 Prefix H323CallSetup Mode Direct/Gatekeeper Ethernet H323CallSetup H323GatekeeperNOTE! The Video Portal needs to reboot before the changes will apply H323Gatekeeper Authentication Mode Auto/Off or c xConfiguration H323Gatekeeper Authentication ID Xconf H323Gatekeeper Authenticationc xConfiguration H323Gatekeeper Authentication Mode Off NOTE! Changes become effective after reboot Services Service 1..64 Enabled On/Off Services Service 1..64 Name S 0 Loadlimit Services Sessionc xConfiguration IP Address Services Service 1..64 ServiceFile S 0 c xConfiguration SIP Interface Server Address SIP Interface Transport Default TCP/UDP/TLSc xConfiguration SIP Mode On c xConfiguration SIP Interface Server Type Auto c xConfiguration SNMP HostIPAddr 1 c xConfiguration SNMP HostIPAddr 2 c xConfiguration SNMP SystemContactc xConfiguration SNMP SystemLocation c xConfiguration SNMP HostIPAddr 3 c xConfiguration ExternalManager Address 4.2.2. General Video Portal CommandsCommand ExternalManager NTP Options c xConfiguration Options 1 Key 115201SS7-1-55C3EBB7 Example 4.2.3. System Status CommandsCommand Dialplan Disk Disk MacAddress Speed Ethernet ExternalManager Feedback 1Ethernet MacAddress 000E0C5CB57D Speed 100full *s/end Status Address Port H323Gatekeeper IPH323Gatekeeper Address Port 1719 *s/end Name Address Port Last Update Last CorrectionNTP Options Address SubnetMask Gateway 10.31.0.1 DNS Server Options Service SystemLoad SystemUnitService SystemLoad ProductType Uptime Software Version Name ReleaseDate Configuration Telephony VideoTelephonyConfiguration Telephony VideoTelephony Hardware Version EP PRI TemperatureCelcius TemperatureFahrenheit Command 4.2.4. Debug Commands4.2.5. Special Xcommand Commands Syslog Level Mask Volume CheckDisk ClearDialplanEntries ClearServiceEntries DefaultValuesSet DefaultValuesSet Level 1Example restore all default factory setting xCommand DefaultValuesSet OK Result parameter Session ID S 1 Example Dial DialplanEntryDelete DialplanEntrySwap DisconnectCallParameters Parameter DialplanEntryNumber Example EraseDisk FeedbackDeregister FeedbackRegister OK Result parameters ID 1 ERROR Result parametersID 1 ERROR Result parameters Expression 1 .. 15 S 0, 256 XPath expression OK Result parameters Example Delete Option Key nr. 1 xCommand OptionKeyDelete OptionKeyAdd OptionKeyDelete RestoreDefaultServicesServiceEntryDelete Parameters ServiceEntryNumberr Parameters ServiceEntryNumberr ServiceEntryNumber2r ServiceEntrySwapExample Delete Service nr. 10 xCommand ServiceEntryDelete Example Swap Service nr. 10 help General User CommandsAbout Help or ? Licence Relkey Xfeedback License Xhistory xhistory ?Examples xhistory call