EDIT Menu

 

 

 

 

 

Marker

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Import Line Data /

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Clear Pattern

 

 

 

 

 

 

 

 

 

 

 

Operation ￿More 3 of 3￿

 

Marker...

 

 

Set High

 

 

 

 

Key Data

 

 

 

 

 

 

1 Bit

 

 

 

 

 

 

 

 

 

Set Low

 

 

 

 

 

 

 

 

 

 

 

4 Bits

 

 

 

 

 

 

 

 

 

Go Back

 

 

 

 

 

 

 

 

 

 

 

Initial Src

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Set Pattern

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

User defined

 

 

 

 

Initial Code

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Code Config...

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Out [I/O]

 

 

 

 

 

 

High/Low

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cancel

 

 

 

 

 

 

 

Invert/Keep

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

O.K.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE. When a new waveform file is created, the marker signal for the first point of the waveform data is set to high as a default value.

The output level for the marker signals is 1.2 V with a termination of 50 W. The marker signals for CH1 are output from the CH1 MARKER 1 output connector on the front panel and CH1 MARKER 2 OUT connector on the rear panel, respectively. Similarly, when Option 02 is installed, the CH2 marker signals are output from the CH2 MARKER 1 OUT and CH2 MARKER 2 OUT connectors, respectively, on the rear panel.

The marker level changes to low after waveform output is complete or when the

STOP button in the MODE menu is pressed.

1.Move the left and right vertical bar cursors to define the area for marker setting, then select Marker... from the third page of the side menu (More 3 of 3).

2.Press the Marker button in the side menu to select marker 1 or marker 2.

3.Press the sub-menu Set High or Set Low button to set the desired marker state. Figure 3 -35 shows marker signal set high between the vertical bar cursors.

￿Set High. The marker signal for the section of the waveform between the vertical bar cursors will be set to High.

￿Set Low. The marker signal for the section of the waveform between the vertical bar cursors will be set to Low

3 ￿58

AWG2021 User Manual