NUGGET 3
GUESTROOM TELEPHONE USERS GUIDE
CONNECTING THE NUGGET 3
Included with the Nugget 3 are (one each): |
|
| |||
• | Base unit | • | Coiled handset cord | • | User guide |
• | Handset | • | Clear plastic overlay | • | Line cord |
Contact your supplier or Teledex for information on ordering custom designed and printed faceplates to enhance the look of your Teledex Nugget 3 telephone.
1)Located on the left side of the Nugget+3 is a modular jack labeled TO HANDSET. Insert one end of the coiled handset cord into this jack (you should hear the coiled cord click when prop- erly inserted).
2)Insert the other end of the coiled handset cord into the modular jack on the handset.
3)Turn the telephone so that the back panel is facing you. Insert one end of the line cord into the jack on the back of the tele- phone labeled LINE.
4)Insert the other end of the line cord into a telephone wall outlet jack.
5)Once your telephone is connected, place the paper faceplate over the keys. The plastic overlay slips into place by hooking the tabs on the overlay into the recessed slots located on both sides. — The overlay is easiest to insert when; the left or right side tabs are inserted first, and the middle part of the overlay is slightly bowed to allow for insertion of the other tabs.
RECEIVING A CALL
1)Lift the handset to connect to the ringing line.
2)To end the call, hang up by replacing the handset.
PLACING A CALL
1)Lift the handset.
2)Listen for dial tone, dial the desired number.
3)To end the call, hang up by replacing the handset.
MESSAGE WAITING LIGHT
The raised red lens is a Message Waiting light. Some telephone systems permit an operator or message center to turn on the red Message Waiting light to alert you that you have a message waiting. Additionally, the Message Waiting light will act as a visual ring indica- tor, flashing when the telephone is ringing.
USING THE DATA PORT
The DATA PORT is a modular jack, located on the back side of the telephone, labeled DATA. You can connect a facsimile, modem, answering machine or other device to the telephone line through the
DATA PORT.
To use the DATA PORT:
Insert the modular line cord from your facsimile machine, modem, etc., into the jack labeled DATA.
ADJUSTING THE RING VOLUME
The Nugget+3 has two ring volume settings.
To change the ring volume:
Locate the adjustment control on the back of the telephone labeled RINGER LOW/HI. Slide the switch to the desired LOW or HI ring vol- ume. The ring volume can be changed at any time.
AUTO DIAL KEYS
The Nugget+3 has 3 programmable AUTO DIAL keys. These keys can be programmed to automatically dial telephone numbers or, to acti- vate telephone system features when connected to a compatible PBX.
The telephone will dial the number each time an AUTO DIAL key is pressed. Some of the AUTO DIAL locations may have been prepro- grammed and labeled before installation.
STORING AUTO DIAL KEYS
To store an AUTO DIAL number:
The telephone must be connected to a telephone jack.
1)Lift the handset.
2)Press the STORE key and release it.
3)Enter the telephone number (including PAUSE* as required - See back page for key location). The dialing sequence can be up to 15 digits.
4)Press the STORE key and release it.
5)Press the AUTO DIAL key where the number is to be stored.
6)Replace the handset.
*A 3.6 second pause can be entered in a dialing sequence by pressing the REDIAL key for each PAUSE required.
REDIAL KEY
To Redial the last telephone number dialed:
1)Lift the handset, listen for dial tone.
2)Press the REDIAL key, the Nugget+3 will dial the last number dialed.
HANDSET VOLUME KEY
The handset has three volume levels. When the handset is first lifted, the handset volume is normal.
To change the HANDSET VOLUME:
Locate the HANDSET VOLUME key to the right of the keypad. Press the key once and the volume level will increase one level (to medium volume).
Press the key once more an the volume level will increase an addi- tional level (to high volume).
To return the handset volume back to normal volume, press the handset volume key again.
FLASH KEY
Pressing the FLASH key initiates a 600ms hookflash. Typical usage is to access PBX/CO features like call waiting.
RMA PROCEDURES
The following procedure should be followed with all Teledex telephone products prior to sending the telephone to the factory for repair.
1)Please perform the tests listed below:
a.Test the telephone on a different telephone jack.
b.Test telephone with a different line cord.
c.Test with a different handset cord (coiled cord).
d.For two line products, please ensure that one of the line buttons is pressed (if both line buttons are in the UP position, the telephone will not operate).
2)If the steps listed above do not provide a remedy for the suspect telephone, please place a tag on the individual telephone describing the defect. Next, call the Teledex Repair Department at 1 (800)
3)Kindly note: An RMA number is unique to each return shipment. Do not duplicate this number on any future shipments.
SHIPPING INSTRUCTIONS:
Please print the RMA number clearly on the outside of your shipping carton(s). Please ship to the following address:
Teledex LLC / RMA#___________
6311 San Ignacio Avenue, San Jose, CA 95119
FREIGHT CHARGES:
The Customer is responsible for shipping products for repair to Teledex. After repair, Teledex will return telephone products to the Customer freight prepaid in the same manner in which is was sent (i.e. Freight sent to Teledex UPS Blue, will be returned via 2 day ship- ping).
**Please note: When telephones are returned for repair due to misuse (i.e. liquid spills, abuse, or Customer modification - warranty label broken), the Customer will be charged the standard repair fee, regard-
