Manuals / Telit Wireless Solutions / Lawn and Garden / Chipper

Telit Wireless Solutions 1vv0300773a manual Packing System, Section A-A

Models: 1vv0300773a

1 64

Download 64 pages 25.29 Kb

Page 59

GE863-PRO3Hardware User Guide

1vv0300773a Rev. 0 - 24/01/08

11.1.5Packing System

According to SMT processes for pick & place movement requirements, Telit GE863-PRO3modules are packaged on trays, each tray contains 20 pieces. Tray dimensions are:

170 ± 0,3

320 ± 0,3

All quotes are in mm, general tolerance ± 0.1

Note that trays can withstand a maximum temperature of 65° C.

Section A-A

6.1

Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved

page 59 of 64

Image 59

Telit Wireless Solutions 1vv0300773a manual Packing System, Section A-A

Contents

GE863-PRO3Hardware User Guide Contents GE863-PRO 3 Hardware User Guide This document is relating to the following products Disclaimer Overview Length 41,4 mm Width 31,4 mm Thickness 3,6 mm GE863-PRO3Mechanical DimensionsTelit GE863-PRO3module overall dimension are GE863-PRO3module connections D10 GND D11 Simvcc D12 Simclk E1 GND E2 Pwrmon DTE GPIO7 / Rftxdisable GSMC2 Vbatt C3 Vrtc C11 Simrst C12 Simio D1 Charge D2 VAUX1ON/OFF*-AP Nrst Reset ARMPB8 PB9PB7 PB0PB2 PB1PA3 HdmbXIN32 XOUT32Reserved GND VBATT2Balls Layout ARM PIO Controller a multiplexing ARM Port IO multiplexingARM PIO Controller B multiplexing ARM PIO Controller C multiplexing Turning on the GE863-PRO3GSM/GPRS Engine Hardware Commands+1,8/5 10kHardware shutdown Hardware Unconditional Reboot of GSM/GPRS Engine2Turning OFF the GE863-PRO3GSM/GPRS Engine Turning ON/OFF the GE863-PRO3ARM ON/OFF*-AP # GND AT+CFUN=4 Power SupplyGSM Power Supply Requirements AT+CFUN=1Vrtc Backup supply ARM Power Supply Requirements817A19A Seiko General Design RulesElectrical design Guidelines Suggested circuit is1.1 + 5V input Source Power Supply Design Guidelines 1.2 + 12V input Source Power Supply Design Guidelines Battery Source Power Supply Design Guidelines Battery Charge control Circuitry Design Guidelines GE863-PRO3Hardware User Guide Thermal Design Guidelines Power Supply PCB layout Guidelines GSM Antenna Requirements Antenna50 ohm GSM Antenna PCB line GuidelinesElectro Magnetic Interference Guidelines GSM Antenna installation GuidelinesOperating Range Interface levels Cmos Level Min Max Logic level specificationsAbsolute Maximum Ratings -Not Functional Parameter Min Max Operating Range Interface levels Cmos Vrtc Level Min Max GSM Gpio Current characteristics Level TypicalCmos 3.1V Current characteristics Level Typical Cmos 1.8V-A Current characteristics Level TypicalSignal Min Max Signal FunctionPhone reset Modem Serial Port Modem Serial Port 2 Debug Serial PortsSignals of the GE863-PRO3GSM/GPRS engine serial port are RS232 level translation An example of level translation circuitry of this kind is GE863-PRO3Hardware User Guide Audio Section Overview Short description Input Lines MicrophoneMicmt 1st differential microphone path Input Lines CharacteristicsOutput Lines Speaker Earmt Differential Line-out Drivers Path Output Lines CharacteristicsEvaluation Kit for Telit GE863- PRO3 Modules ON/OFF 10 GSM/GPRS General Purpose I/O10.4Using the Rftxmon Output GPIO3 Using a Gpio Pad as InputUsing a Gpio Pad as Output Using the RF Transmission Control GPIO7Using the Buzzer Output GPIO4 Using the Alarm OutputDevice Status 10.7Indication of network service availabilityLED status RTC Bypass out 10.9VAUX1 power outputOperating Range VAUX1 power supply PCB pad Design Mounting the GE863-PRO3on the Application Board11.1General StencilSolder paste Following is the recommended solder reflow profile 11.1.4 GE863-PRO3Solder Reflow3C/second max Section A-A Packing SystemModules orientation on tray Moisture Sensibility Conformity Assessment Issues Safety Recommandations Revision Date Changes Document Change Log