Manuals / Toshiba / Photography / Digital Camera

Toshiba IK-TF9C 1P SR 1 Pulse Trigger Sync Reset, Pulse Trigger SYNC-RESET Picture Output Timing

Models: IK-TF9C

1 32

Page 25

( 2 ) 1P SR (1 Pulse Trigger Sync Reset)

Charge begins to accumulate after the trigger input to CC1 of the DIGITAL terminal, the vertical sync signal is reset and frame images are output.

(2. 1) 1 Pulse Trigger SYNC-RESET Picture Output Timing

Negative polarity mode

Trigger*1

Positive polarity mode

About 1 ∝s

Exposure period*2

Exposure completion

0 to 2H*3

(Internal VD)

RGB data (video interval image)

FVAL

LVAL,

DVAL

58H (Partial scanning OFF)

56H (Partial scanning 30fps)

78H (Partial scanning 40fps)

*1: Externally input signal

*2: Exposure time is determined by the setting of "7. 2 (1.3) Changing each setting in E.TRG mode".

*3: VD is generated after 0 to 2H following the completion of the exposure period and the video is synchro- nized to this and output.

Note:

When the next trigger is input before completion of the output of the video corresponding to the trig- ger, there will be an effect on the video.

Page 25

Image 25

Toshiba IK-TF9C instruction manual 1P SR 1 Pulse Trigger Sync Reset, Pulse Trigger SYNC-RESET Picture Output Timing

Contents

Following information is only for EU-member states For Customer UseSafety Precautions Disclaimer Avoid setting in humid, smoky, vaporized or dusty placesTable of Contents Components Names and Functions Connection Connector Pin AssignmentsStandard Connection White Balance OperationAutomatic White Balance Manual White Balance Result displayed MeaningReasons. Such as no white area is included in an object, etc Shutter speed mode is E.TRG modeAvailable selections Preset value Items Controlled by Using on Screen DisplayUsing the Menus Mode Setting by on Screen DisplayDisp TRG 1P SNR 1P SR TRG PW SNR TRG PW SRShutter Electronic shutter MenusFlicker may be large TRGPartial scanning setting Changing each setting in Manu modeChanging the shutter speed Mode = SS Changing each setting in SS synchro. scan modeChanging the shutter speed setting Changing each setting in 1P SNR mode Changing each setting in E.TRG modeChanging the polarity of inputting trigger pulse setting Changing 1P SNR exposure time settingMode = E.TRG E.TRG = 1P SR Changing each setting in 1P SR modeChanging 1P SR exposure time setting Mode = E.TRG E.TRG = PW SNR Changing each setting in PW SNR modeMode = E.TRG E.TRG = PW SR Changing each setting in PW SR modeChanging the gain in Manu mode Changing each setting in GainGain Video gain WHT BAL White balance Changing gamma correction MANU/OFFChanging master pedestal Changing R pedestalChanging the shading correction mode Setting to factory setting statusChanging the manual shading correction setting OptionSetting by 2H Setting by the frameSynchro. Scan Operation Fval Lval Davl1 Pulse Trigger SYNC-NON Reset Picture Output Timing 1P SNR 1 Pulse Trigger Sync Non ResetE. TRG External trigger Fval Lval Dval1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Trigger Sync ResetPulse Width Trigger SYNC-NON Reset Picture Output Timing PW SNR Pulse width trigger SYNC-NON Reset1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESETPartial Read When Partial Scanning Mode is onPartial Scanning OFF All pixels scanning Partial Scanning onHorizontal Output Waveform Timing Chart Output Waveform Timing ChartVertical Output Waveform Timing Chart Fval LVAL、 DvalRGB, 3CCD SpecificationsBefore Making a Service Call External Appearance DiagramSymptom Items to be checked Step-by-step Procedures How to Obtain Warranty Service Limited One 1 Year Warranty of Labor and PartsImaging Systems Division