Toshiba SD-690KR manual Night Mode, Digital Output, Down Sampling, 3D Effects

DVD Menu Options

English

versa. Choose zero (0) to balance the contrast.

Tint

Increase the value to darken the picture or vice versa. Choose zero (0) for average setting.

Color

Increase the value to enhance the colour in your picture or vice versa. Choose zero (0) to balance the colour.

EPress  /  to adjust the setting that best suits your personal preference.

FRepeat steps D~ E to adjust your picture preference.

GPress  /  to select ＇Close＇ and press OK to confirm.

Using the Audio setup menu

Night Mode

This mode optimizes playback of sound at low volume. High volume outputs will be softened and low volume outputs are brought upward to an audible level.

AIn ＇ Audio＇, press  /  to select { Night Mode }, then press .

{On }

Select this to set low volume output. This feature is only available for movie discs with Dolby Digital

mode.

{Off }

Turns off night mode feature. Select this to enjoy the surround sound with its full dynamic range.

BUse  /  to select a setting and press OK to confirm.

APress SETUP on the remote control. The system setup menu appears.

Language	Digital Output	: All
	Night Mode	: Off
Video	Down Sampling	: On
	3D Effects	: Off
Audio

Rating

Misc

BPress  /  to select { Audio }, then press .

CPress  /  to select an item, then press  to access.

Example: { Night Mode }

The options for the selected item appears.

If the selection in the menu is greyed out, that means the feature is not available or not possible to change at the current state.

DUse  /  to select a setting and press OK to confirm.

Example: { On }

The setting is selected and setup is completed.

ETo exit, press SETUP.

Digital Output

Select this if you connect to a multichannel decoder/ receiver.

AIn 'Audio', press  /  to select { Digital Output }, then press .

{ All }

Select this if the connected device has a built-in multichannel decoder that supports one of the multichannel audio format (Dolby Digital, DTS).

{PCM }

Select this if the connected device is not capable of decoding multichannel audio. The DVD player will convert the Dolby Digital signal to PCM (Pulse Code Modulation).

{Off }

To deactivate the digital audio output. For example, if you use the AUDIO OUT jacks to connect to a TV or stereo system.

BUse  /  to select a setting and press OK to confirm.

Tip:

-When playing MPEG, MP3 and set Digital Output to {All}, the player will output PCM signals.

Helpful hint: Press  to go back to previous menu item. Press SETUP to exit the menu item.

Down Sampling

You can enable and disable the digital signal for better sound output quality.

AIn ＇Audio＇, press  /  to select { Down

Sampling }, then press .

{Off }

If your amplifier / decoder is compatible with 96 KHz PCM, select “ Off “ . Sound is sampled at 96 KHz.

{On }

If your amplifier / decoder is not compatible with 96 KHz PCM, select “ On “ . Sound recorded at 96 KHz is down sampled to 48 KHz.

BUse  /  to select a setting and press OK to confirm.

Tip:

- When playing back disc with copyright protection, the sound will be down sampled to 48 KHz even when you select Down Sampling off.

3D Effects

To obtain expansive virtual surround sound effects from two speakers, set 3D Effects to on. This enhancement sounds only output from the Analogue AUDIO OUT (L / R) jacks of the DVD player.

AIn 'Audio', press  /  to select { 3D Effects }, then press .You can set to { Off } or { On }.

BUse  /  to select a setting and press OK to confirm.

Tip:

- Only effective in playback of a DVD Video disc with Dolby Digital 5.1 bitstream.

Using the Rating setup menu

APress SETUP on the remote control. The system setup menu appears.

Language Parental control : 8.Aduit

Set Password

Video

Audio

Rating

Misc

BPress  /  to select {Rating }, then press .

19