Connection
English Français Español Deutsch Italiano Português Svenska
Turning the power on and off
Before connection
•Read the owner’s manual of the device you are connecting to the projector.
•Some types of computer cannot be used or connected to this projector. Check for an RGB output terminal, supported signal p.39 , etc.
•Turn off the power of both devices before connecting.
•The figure below is a sample connection. This does not mean that all of these devices can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)
■Connecting the power cord
1Insert the power cord connector into the AC IN socket of the projector.
2Insert the power cord plug into a wall or other power outlet.
Power cord connector (Supplied)
Computer (for control)
Video recorder, |
|
DVD player, etc. | VCR, etc |
■Removing the lens cover
Be sure to remove the lens cover when the power is turned on. If it is left on, it could become deformed due to heat.
To
To | p.43 | output | |
terminal | |||
| |||
|
|
|
|
|
|
| Control cable |
| |||||||||
|
|
|
|
|
| (supplied) | |||||||||
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
RGB component video cable (not supplied)
To Y/CB/CR output
Green (Y)/Blue (CB)/Red (CR)
DVD video recorder, etc.
To video
output
Video cable (supplied)
| DVI cable |
| (not supplied) |
RGB cable |
|
(not supplied) | To DVI output |
| |
To RGB output |
|
■ Turning the power on
1 Turn on the main power switch
The ON indicator will change to orange, indicating standby mode.
•After the main power switch is turned on, the inner cooling fan starts cooling.
2 Press the ON/STANDBY button.
The power turns on, and the following 3 green indicators light: ON, LAMP, and FAN. After a moment, the
Remote Control panel Control
(Orange) 
Operations
Computer
Computer
CAUTION
• | Do not look into the lens while the lamp is on. The strong light from the lamp may cause |
| damage to your eyes or sight. |
• | Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating. |
• | Do not place your hands, face, or other objects near the air exhaust. Doing so could cause |
Notes
•If you want to feed the digital RGB signal, separately available DVI cable is needed.
•If you are using the digital RGB signal for input to this unit, some computer models or a certain type of DVI cable may cause on rare occasions noise on the screen. If such is a case, decrease your computer’s refresh rate or the resolution. It is also recommended to use a DVI cable in 2 m or less in length.
burns, deform/break the object. |
20 | 21 |
