Toshiba TLP-T50M owner manual Using handy features, Basic operations

Basic operations (Continued)

5Projector placement angle adjustments

Using handy features

■Using auto setting (Auto setting)

The placement angle and the height of the projected image can be adjusted by the foot adjuster.

q Lift up the front of the projector until	1
it is at the desired angle, then press
the foot adjuster release button.
The foot adjuster extends. Release the
button to lock the position.
w Turn the foot adjuster to fine-tune
the angle.	2	3

This function sets up the projector to the optimum state for each type of the input signal by using simple operations.

1Press the AUTO SET button.

The Auto setting menu appears.

2Press the AUTO SET button again.

The menu item is automatically adjusted/set.

For computer input, the icon will appear during processing.

Control panel

FAN TEMP LAMP ON

INPUT	ON / STANDBY
	MENU
VOL. -	VOL. +
AUTO
KEYSTONE	AUTO SET

Remote Control

	ON/
CALL	STANDBY
KEYSTONE AUTO	SET
MUTE	FREEZE

RESIZE

RESIZE

OFF

INPUT

e To adjust the horizontal angle, use the tilt adjuster.

To stow the foot adjuster, hold up the projector while pressing the foot adjuster release button, then slowly lower the projector will the button depressed.

6Adjusting the picture size and focus

q Use the zooming lever to adjust the screen	1
size.
w Use the focusing ring to adjust the focus.	2

7Adjusting the volume with the buttons

The speaker volume can be adjusted when an audio signal is being input.

Notes

•Note that the lamp characteristics may rarely cause the brightness to fluctuate slightly.

•A lamp is consumable supplies.

If used for extended periods, images will appear dark, and the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime of the lamp depends on conditions of use.)

•The LCD panel is made using extremely advanced technology, but there may be black spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Please note that these are not malfunctions.

•Although this projector supports a wide range of RGB signals p.36 , any resolutions not supported by the model (XGA or SVGA, depending on the model) will be expanded or shrunk, which will affect image quality slightly. To view high-quality images, it is recommended that the computer’s external output should be set to the projector’s resolution.

•With some models of computer having LCD displays or the like, displaying images simultaneously on the projector and the monitor’s display may prevent the images from displaying properly. If this happens, turn off the computer’s LCD display. For information on how to turn off the LCD display, see the owner’s manual of your computer.

•If a signal not supported by the projector is input, the icon will appear.

•If a no signal is being input from the connected device, the icon will appear.

•If an unavailable operation button is pressed, the icon will appear.

Note

•Auto adjustment/setting may not be performed correctly for input signals other than those supported by the projector p.36 , p.37 .

●Manual adjustment and setting

The menu items vary according to the input type, as shown in the table below.

Use the buttons to adjust the items in the table below, then press the button when you are finished. The menu disappears.

Input		Item			Description
Computer		Phase	Adjust with		to eliminate flicker.
	Item
		Frequency	Adjust with		to eliminate periodic patterns and
	Select		flickering when many vertical lines appear in the screen.
		H-position	Move left		Move right
		V-position	Move up		Move down
Y/PB/PR		Phase	Adjust with		to eliminate flicker.
	Item	Signal format	[	: Enter to setting mode]		[	: Select one
			of the following]		[Apply:	]
	Select		480i(525i)@60Hz/480p(525p)@60Hz/
			576i(625i)@50Hz/576p(625p)@50Hz/
			720p(750p)@60Hz/720p(750p)@50Hz/
			1080i(1125i)@60Hz/1080i(1125i)@50Hz/
			1035i(1125i)@60Hz/1152i(1250i)@50Hz
Video		Video mode	[	: Enter to setting mode]		[	: Select one
S-video			of the following]		[Apply:	]
			NTSC/PAL/SECAM/PAL-N/PAL-M/PAL60/NTSC4.43

Operations

22 23