Toshiba V.90 AT command set result codes 47

S-Registers

AT command set result codes 47

ERROR 4 Invalid command

CONNECT 1200 EC*5 Connection at 1200 bps

NO DIAL TONE 6 No dial tone detected

BUSY 7 Busy signal detected

CONNECT 2400 EC*10 Connection at 2400 bps

CONNECT 4800 EC*11 Connection at 4800 bps

CONNECT 9600 EC*12 Connection at 9600 bps

CONNECT 14400 EC*13 Connection at 14400 bps

CONNECT 19200 EC*14 Connection at 19200 bps

CONNECT 7200 EC*24 Connection at 7200 bps

CONNECT 12000 EC*25 Connection at 12000 bps

CONNECT 16800 EC*86 Connection at 16800 bps

CONNECT 300 EC*40 Connection at 300 bps

CONNECT 21600 EC*55 Connection at 21600 bps

CONNECT 24000 EC*56 Connection at 24000 bps

CONNECT 26400 EC*57 Connection at 26400 bps

CONNECT 28800 EC*58 Connection at 28800 bps

CONNECT 31200 EC*59 Connection at 31200 bps

CONNECT 33600 EC*60 Connection at 33600 bps

CONNECT 38400 EC*28 Connection at 38400 bps (DTE

rate)

Command Set Result Codes Table (Continued)

Result Code Numeric Description

* EC appears only when the Extended Result Codes configuration option is enabled. EC is replaced

by one of the following symbols, depending upon the error control method used:

V.42bis - V.42 error control and V.42bis data compression

V.42 - V.42 error control only

MNP 5 - MNP class 4 error control and MNP class 5 data compression

MNP 4 - MNP class 4 error control only

NoEC - No error control protocol

Contents

Main ii FCC Notice Declaration of Conformity Information iii Industry Canada Requirement Pursuant to FCC CFR 47, Part 68: Type of service iv If problems arise Disconnection Fax branding Instructions for IC CS-03 certified equipment v 2 3 Copyright vi Disclaimer Trademarks vii Contents viii Chapter 3: AT Commands........................................................ 13 ix Chapter 4: S-Registers.............................................................. 39 x Page xii Introduction xiii Features xiv xv Function charts The chart below lists the internal modems supported communication protocols: xvi Users guide contents xvii Conventions Abbreviations Keys Key operation xviii Display Messages Page Setup Hardware Setup Function check Page Page Using the Internal Modem Connection procedures Analog or digital? Connecting the internal modem Disconnecting the internal modem Basic operation Connecting to a telephone line Direct access line Extension line Receiving a call Terminating a call Setting the data flow control CTS/RTS control XON/XOFF control Page Page AT Commands AT command formats +++ Escape sequence A/ Repeat last command A Answer command Bn Communication standard setting Dn Dial En Echo command Hn Hook control AT command formats 17 Result Codes: In Request ID information This command displays product information about the modem. Page Page Ln Monitor speaker volume Mn Monitor speaker mode Nn Modulation handshake On Return online to data mode P Select pulse dialing Qn Result code control T Select tone dialing Vn DCE response format Wn Result Code Option Xn Result code selection, call progress monitoring AT command formats Extended result codes Dial tone detect Busy tone detect Zn Recall stored profile &Cn Data Carrier Detect (DCD) control &Dn Data Terminal Ready (DTR) control &F Load factory settings &Gn V.22bis guard tone control &Kn Local flow control selection &Pn Select Pulse Dial Make/Break Ratio &Tn Self-test commands &V View active configuration and stored profile AT command formats 29 Press any key to continue; Esc to quit. &W Store current configuration &Zn=x Store telephone number \Nn Error control mode selection Qn Local flow control selection \Vn Protocol result code %Cn Data compression control -V.90=<n> +MS Command +MS= <carrier>, <automode>, <0>, <max_rate>, <0>, <max_rx_rate> +MS? +MS=? Page Page Page S-Registers S-Register values S0 Auto answer ring number S1 Ring counter S2 AT escape character (user-defined) S3 Command line termination character (user-defined) S4 Response formatting character (user-defined) S5 Command line editing character (user defined) S6 Wait before dialing S7 Connection completion time-out S8 Comma pause time S10 Automatic disconnect delay S11 DTMF dialing speed S12 Escape guard time S37 Dial line rate S38 K56flex Dial line rate S38 56K Downstream Rate AT command set result codes The following table shows the result codes. AT command set result codes 47 Page AT command set result codes 49 Page Page MNP and V.42 Error-correction overview MNP error correction V.42 error correction Operation modes Normal mode Reliable mode Commands (\Nn ) Flow control Serial port flow control XON/XOFF flow control (software) CTS/RTS two-way flow control (hardware) Commands (\Qn, &Kn) Modem port flow control Data compression Commands (%Cn) Page Test Function Test description Testing procedure Page Page Specifications Network control unit (NCU) Specifications Communication specifications Page Communication Conditions Communication parameters Select communication parameters from the table below. Telephone line types Connectable lines (2-wire) Unconnectable lines (4-wire) Dial modes Page Glossary Acronyms A Glossary 71 B C Glossary 73 D E Glossary 75 F G H I K M Glossary 77 N O P R S Glossary 79 T U X Index Numerics A Index 81 C D E F G M N O P R