Toshiba WAL7C Assemble TV set body and stand fix type, Model applicable 19AV550 Series

Model applicable : 19AV550 Series

Assemble (TV set body and stand fix type)

(1)Please take out the LCD color TV from the

LCD TV case.

(2)Remove the stand part from the LCD TV.

1Rotate the TV stand to its position generally used. To avoid scratching the LCD screen, please place a soft cloth on a table etc, and then put the LCD TV on the cloth with its screen facing down.

2Remove the 4 screws used to fix the stand.

3Remove the stand from the TV.

4 securing screws

Remove the stand

Stand part

*Please keep to the stand and fix screws.

(3)Attach the bracket of TV side to the LCD

color TV.

1 Tear off adhesive tapes of the supplied (four) paddings, align its hole with fixing bolts, and affix it to the screw place of TV side.

2Align the screw hole of bracket of TV side with which

of the TV, attach the bracket firmly to the TV with four supplied screws (M4 ⋅ 14mm).

To fix at 4 outer side holes

Spacer

TV mounting bracket

Caution

The supplied screws and paddings should be

used.

Other screws and paddings may cause function change, electric shock (in case of long screws), or lead to insufficient strength (in case of short screws) etc.

■ Parts list

Product name	Quantity
TV side bracket	1
Wall-mount bracket	1
Tilt-adjustable bracket	1
Tilt-adjustable bracket securing screw	4
(M5 ⋅ 14mm)
Screw (M4 ⋅ 14mm)	4
Spacer (with tape attached)	4

Nominal method of screws is as below.

t=1.8

FLAT WASHER

SPRING WASHIER

M4

14

(4)Assemble the tilt-adjustable bracket,

adjust the angle.

1Assemble the wall-mount bracket and the tilt-adjust- able bracket with 2 tilt-adjustable bracket securing screws threading through the rotation center hole. (Slightly tighten the 2 screws.)

Wall-mount bracket Rotation center

Tilt-adjustable bracket

2Move the tilt-adjustable bracket to align it with the closet hole according to your preference angle, then fix it temporarily with 2 securing screws.

Tilt-adjustable bracket

Wall-mount bracket

3After installing the TV, confirm the preference angle with the customers and make adjustment accord- ing to the points described in (2) above. After mak- ing adjustment, tighten firmly the 4 securing screws mentioned in (1) and (2) above to fix the tilt-adjust- able bracket fully.

(5)Attach the Wall-mount Bracket.

Attach the wall-mount bracket to the wall with 4 com- mercial available screws or expansion anchor bolts, re- ferring to the bottom right table.

(4 positions shown as below)

Be sure to fix the screws into the strong and reliable wood or post inside the wall firmly.

(Attaching on the boards such as thin complex board/ plasterboard will be very dangerous, so please be sure to avoid such places.)

■Determine the Position before Attaching the Wall-mount Bracket

The relationship of position for the LCD TV and the Wall-mount bracket is shown as below. Please ask the customers to decide the position of the TV in advance, and then attach the bracket.

Lower side of Wall-mount

Bracket

149mm

■Angle adjustment of the LCD TV is shown as below

the 1st hole from the top tilt upwards 20 degrees the 2nd hole tilt upwards 10 degrees the 3rd hole tilt 0 degree

the 4th hole tilt downwards 10 degrees the 5th hole tilt downwards 20 degrees

LCD TV side

(6)Attach the LCD TV to the tilt-adjustable

bracket installed on the wall.

1Align the bracket holes on the rear of the LCD TV with the hooks of the tilt-adjustable bracket, and then hook the TV.

(This illustration is drawn as you can see through the TV.)

Hook

2By slightly lowering the LCD TV, you can hitch it on the hook.

Slightly lower to hitch it on the hook

3Move left the LCD TV to lock it. Make sure that the TV will not fall off.

Move left to lock it

■Wall material/Screw, Expansion Anchor Bolt Corresponding Table

Wall material	Expansion anchor bolt/
	screw used
Plasterboard/	fix into the post inside the wall
Complex board	the screw firmly fixable into the
(less than 10mm)	post inside the wall
Complex board	tapping screw (ø 4 ⋅ 18)
(above 10mm)
Wood post	tapping screw (ø 4 ⋅ 18)
Concrete	expansion anchor bolt (T-660)