Transcend Information CF 266X instruction

TS2G~8GCF266		266X CompactFlash Card

Table: Ultra DMA Termination with Pull-up or Pull down Example

¾Printed Circuit Board (PCB) Trace Requirements for Ultra DMA On any PCB for a host or device supporting Ultra DMA:

9The longest D[15:00] trace shall be no more than 0.5" longer than either STROBE trace as measured from the IC pin to the connector.

9The shortest D[15:00] trace shall be no more than 0.5" shorter than either STROBE trace as measured from the IC pin to the connector.

¾Ultra DMA Mode Cabling Requirement

9Operation in Ultra DMA mode requires a crosstalk suppressing cable. The cable shall have a grounded line between each signal line.

9For True IDE mode operation using a cable with IDE (ATA) type 40 pin connectors it is recommended that the host sense the cable type using the method described in the ANSI INCITS 361-2002 AT Attachment - 6 standard, to prevent use of Ultra DMA with a 40 conductor cable.

Transcend Information Inc.

16

Image 16

Transcend Information CF 266X dimensions ¾ Ultra DMA Mode Cabling Requirement

Contents

Placement Features Dimensions266X CompactFlash Card Description Transcend Block Diagram Pin Assignments and Pin Type TS2G~8GCF266 Signal Description TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 Electrical Specification „ Output Drive Type „ Output Drive Characteristics „ Signal Interface „ Additional Requirements for CF Advanced Timing Modes 266X CompactFlash Card „ Ultra DMA Electrical Requirements¾ Series termination required for Ultra DMA operation Table Typical Series Termination for Ultra DMA ¾ Ultra DMA Mode Cabling Requirement „ Attribute Memory Read Timing Specification TS2G~8GCF266 „ Common Memory Read Timing Specification „ Common Memory Write Timing Specification „ I/O Input Read Timing Specification TS2G~8GCF266 „ I/O Output Write Timing Specification TS2G~8GCF266 „ True IDE PIO Mode Read/Write Timing Specification TS2G~8GCF266 „ True IDE Ultra DMA Mode Read/Write Timing Specification Table Ultra DMA Data Burst Timing 266X CompactFlash Card TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 „ Single Function CF+ Cards Card Configuration„ Multiple Function CF+ Cards TS2G~8GCF266 „ Attribute Memory Function Attribute Memory Function TS2G~8GCF266 TS2G~8GCF266 „ Pin Replacement Register Base + 04h in Attribute Memory „ Socket and Copy Register Base + 06h in Attribute Memory Table Pcmcia Mode I/O Function Transfer Function Common Memory Transfer Function Table Common Memory Function True IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol „ I/O Primary and Secondary Address Configurations Table Primary and Secondary I/O Decoding „ Contiguous I/O Mapped Addressing Table Contiguous I/O Decoding „ True IDE Mode Addressing „ Memory Mapped Addressing „ CF-ATA Registers ¾ Data Register Address 1F0h170hOffset 0,8,9 ¾ Sector Count Register Address 1F2h172h Offset ¾ Sector Number LBA 7-0 Register Address 1F3h173h Offset¾ Cylinder High LBA 23-16 Register Address 1F5h175h Offset ¾ Drive/Head LBA 27-24 Register Address 1F6h176h Offset TS2G~8GCF266 ¾ Device Control Register Address 3F6h376h Offset Eh ¾ Card Drive Address Register Address 3F7h377h Offset Fh CF-ATA Command Set „ Check Power Mode 98h or E5h „ Execute Drive Diagnostic 90h „ Erase Sectors C0h „ Flush Cache E7h „ Format Track 50h „ Identify Device Ech 266X CompactFlash Card ¾ Word 0 General Configuration ¾ Word 1 Default Number of Cylinders ¾ Word 3 Default Number of Heads¾ Word 6 Default Number of Sectors per Track ¾ Word 49 Capabilities Bit 13 Standby Timer ¾ Multiple Sector Setting ¾ Total Sectors Addressable in LBA Mode¾ Translation Parameters Valid ¾ Current Number of Cylinders, Heads, Sectors/Track ¾ Words 82-84 Features/command sets supported ¾ Word 65 Minimum Multiword DMA transfer cycle time¾ Recommended Multiword DMA transfer cycle time ¾ Word 68 Minimum PIO transfer cycle time with Iordy ¾ Words 85-87 Features/command sets enabled ¾ Word 88 Ultra DMA Modes Supported and Selected ¾ Word 89 Time required for Security erase unit completion ¾ Word 91 Advanced power management level value ¾ Word 160 Power Requirement Description¾ Word 128 Security Status Bit 8 Security Level Additional Requirements for CF Advanced Timing Modes TS2G~8GCF266 „ Idle 97h or E3h „ Initialize Drive Parameters 91h „ Idle Immediate 95h or E1h„ NOP 00h „ Read Buffer E4h „ Read DMA C8h „ Read Long Sector 22h or 23h TS2G~8GCF266 „ Recalibrate 1Xh „ Request Sense 03h „ Seek 7Xh „ Set Features EFh Feature Supported 266X CompactFlash Card „ Standby Immediate 94h or E0h „ Translate Sector 87h Translate Sector Information „ Wear Level F5h „ Write Buffer E8h „ Write DMA CAh TS2G~8GCF266 TS2G~8GCF266 „ Error Posting TS2G~8GCF266