Transition Networks CFETF1011-205 Contact Us, Installation, Set the 4-Position Switch

CFETF10xx-205

Contact Us

Technical Support

Technical support is available 24 hours a day.

US and Canada: 1-800-260-1312

International: 00-1-952-941-7600

Transition Now

Installation

CAUTION: Wear a grounding device and observe electrostatic discharge precautions when setting the 4-position switch and the jumpers. Failure to observe this caution could result in damage to, and subsequent failure of, the media converter.

Chat live via the Web with Transition Networks Technical Support. Log onto www.transition.com and click the Transition Now link.

Web-Based Seminars

Transition Networks provides seminars via live web-based training. Log onto www.transition.com and click the Learning Center link.

Set the 4-Position Switch

•The 4-position switch is located on the circuit board.

•Use a small flat-blade screwdriver to set the recessed switches.

Auto-Negotiation (up = enabled)

Pause (up = enabled)

Link Pass Through (up = enabled)

Far End Fault (up = enabled)

1 2 3 4

E-Mail

Ask a question anytime by sending an e-mail to our technical support staff. techsupport@transition.com

Address Transition Networks

10900 Red Circle Drive Minnetonka, MN 55343, U.S.A.

telephone: 952-941-7600

toll free:800-526-9267

fax:952-941-2322

	Declaration of Conformity
Name of Mfg:	Transition Networks
	10900 Red Circle Drive, Minnetonka MN 55343 U.S.A.
Model:	CFETF10xx-205 Series Media Converters
Part Number(s):	CFETF1011-205, CFETF1013-205, CFETF1014-205, CFETF1015-205,
	CFETF1016-205, CFETF1017-205, CFETF1018-205, CFETF1019-205,
	CFETF1039-205
Regulation:	EMC Directive 89/336/EEC

Purpose: To declare that the CFETF10xx-205to which this declaration refers is in conformity with the following standards.

CISPR 22: 1997+A1:2000; EN 55022:1998 A1:2000 Class A & B; EN 55024:1998; FCC Part 15 Subpart B; EN 61000-2-3:1995 A14:2000, EN 61000-3-3:1995; 21 CFR subpart J

1.Auto-Negotiation

up	= Advertises 100 Mb/s Full-Duplex and Half-Duplex (only during
	Auto-Negotiation).

down = Disables Auto-Negotiation. Operates at 100 Mb/s in the mode (either full- or half-duplex)of the attached device.

2.Pause

(Applies ONLY if switch “1” is up AND the media converter is connected to auto negotiating device(s) capable of Pause Control Frame.)

up = Allows negotiation of Pause Control Frame.

down = Does not allow negotiation of Pause Control Frame.

3.Link Pass-Through

up = Enables Link Pass-Through.

down = Disables Link Pass-Through.

4.Far-End Fault

up = Enables Far-End Fault.

down = Disables Far-End Fault.

Set the hardware/software Jumper

•The header for the jumper is located on the circuit board labeled “H” hardware mode and “S” software mode.

•Use small needle-nose pliers to remove and position the jumper.

I, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s) and Standard(s).

	May, 2008___
Stephen Anderson, Vice-President of Engineering	Date

Hardware The four DIP switches control the function of the board in hardware mode. You can only view status via the Web or Focal Point interface.

Software Software controls the function of the board. The DIP switches do not function in software mode.

H S

Hardware Mode

H S Software Mode

14 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 techsupport@transition.com -- Click the “Transition Now” link for a live Web chat. 3