Transition Networks SSDTF1012-100, SSDTF1022-100, SSDTF1011-100 Installation, Cable Specifications

INSTALLATION

CAUTION: Wear a grounding device and observe electrostatic discharge precautions when setting switch and when installing Media Converter Slide-in- Module in the Media Conversion Center. Failure to observe this caution could result in damage to, and subsequent failure of, the Media Converter Slide-in- Module.

Set Loopback Test Switch

NOTE: The Loopback Test switch, located on Media Converter Slide-in-

Module front panel, allows the network administrator
	Loop
to enable a loopback test for installation and network
debug procedures.

Use small flatblade screwdriver or similar device to set recessed switches. Refer to drawing for switch locations.

Set MDI/MDI-X Switch

NOTE: The MDI/MDI-X switch allows the network administrator to use straight-through cable in installations where crossover-configuration cable is required.

Use small flatblade screwdriver or similar device to set recessed switches. Refer to drawing for switch settings.

CABLE SPECIFICATIONS

Fiber Cable

Bit error rate: ≤ 10-9

MULTIMODE

Fiber Optic Cable Recommended:	62.5	/ 125 µm multimode fiber
Optional:	100 / 140 µm multimode fiber
	85 / 125 µm multimode fiber
	50 / 125 µm multimode fiber
SSDTF1011-100	850 nM
Fiber Optic Transmitter Power:	min: -14.0 dBm		max: -12.0 dBm
Fiber Optic Receiver Sensitivity:	min: -25.0 dBm		max: -12.0 dBm
Typical Maximum Cable Distance*:	2 kilometers
SSDTF1013-100	850 nM
Fiber-optic Transmitter Power:	min: -14.0 dBm		max: -12.0 dBm
Fiber-optic Receiver Sensitivity:	min: -25.0 dBm		max: -12.0 dBm
Typical Maximum Cable Distance*:	2 kilometers
SINGLEMODE
Fiber Optic Cable Recommended:	9 µm singlemode fiber
SSDTF1012-100	1300 nM
Fiber-optic Transmitter Power:	min: -21.0 dBm		max: -14.0 dBm
Fiber-optic Receiver Sensitivity:	min: -25.0 dBm		max: -14.0 dBm
Typical Maximum Cable Distance*:	8 kilometers
SCSDTF1014-100	1300 nM
Fiber-optic Transmitter Power:	min: -21.0 dBm		max: -14.0 dBm

Twisted Pair #1

Twisted Pair #2

MDI

1	RTIP	TTIP	Twisted
2	RRING	TRING	Pair	#1
4	TTIP	RTIP	Twisted
5	TRING	RRING	Pair	#2

Connectors for unlike devices

		MDI-X
1
	RTIP		RTIP
2	RRING		RRING
4	TTIP		TTIP
5	TRING		TRING

Connectors for like devices

Fiber-optic Receiver Sensitivity:	min: -27.0 dBm	max: -14.0 dBm
Typical Maximum Cable Distance*:	8 kilometers
SSDTF1015-100 (long haul)	1300 nM
Fiber-optic Transmitter Power:	min: -15.0 dBm	max: -5.0 dBm
Fiber-optic Receiver Sensitivity:	min: -27.0 dBm	max: -14.0 dBm
Typical Maximum Cable Distance*:	15 kilometers
SSDTF1022-100 (long haul)	1300 nM
Fiber-optic Transmitter Power:	min: -15.0 dBm	max: -5.0 dBm
Fiber-optic Receiver Sensitivity:	min: -25.0 dBm	max: -14.0 dBm
Typical Maximum Cable Distance*:	15 kilometers

*Actual distance dependent upon physical characteristics of network installation.

Set 8-Position Switch

NOTE: An eight-position switch allows the network administrator to configure the media converter for network conditions.

Use small flatblade screwdriver or similar device to set recessed switches for site installation. Refer to drawings at right for eight-position switch settings.