Tribest FS-610 manual Like the picture next to it, Tail

NoteTIPSips forFORextractingEXTRACTING

PleasePleasereadreadbeforebefore juicethe xtractionextraction. .

Inserting the food one by one could extract properly

1. Feed the foods into the Feeding Chute piece by piece in order to properly extract juice without clogging.

ber materials(celery or water parsley) into right amount to get the good

resuloptimal(4-5inch)results.For. bettForervenresult,bettercut theresults,materialcutbythe1inchfoodsandtoinserta widthoneofby1oneinch. and insert the pieces one by one.

3
. When extracting carrot juice, pleaserentcu fruitscarrotswithintoa lothalvesof moistureor quartersto get morein

ber. Please cut carrot into quarters before erent amount of juice to

4. While in use, the appliance may make a noise. This does not constitute that extract.)

the appliance has a problem with operation.

5. You must remove seeds from foods such as peaches and plums.

If the food is not fresh, the amount of juice will be less. To get more juice, dip it in the

6clean.Fullywaterdefrostun ilfrozenthe materfruitsal getswhenwetyou.Then,makethefroodzenwillfruithavesorbetmore. juiceFeedingto behardextract. frozen fruit may damage the juicing system.

7Some
. Do nfotodoverfeeddoes nottohaveavoidjuicecloggingthat can bethextrmactedhine. .

8.Some portion of grounded fruit or vegetable may splash out occasionally if While
the plungerin se, theisapplianot inceusemight. be making a noise. However, the appliance has no

problem with operation.

There
might be a kick-back from the extraction of fruits and vegetables. Be aware.

Materials like Peach, Plum, or persimmon need to be removed the seed. Defrost

frozen fruits and you use with milk or beverages slowly.

TIPSSipsliconeFORfor siliconepartsSILICONEtipspartsPARTS

5*1

SiliconeSiliconepartspartsareareableabletotobebewasheddisassembled. Dry theandpartswashedafter.washingFully dry. Pleasethe siliconecheckpartsif theafter siliconewashingparts. Pleasearecheckpla edifcorrectlythe silicone. parts are placed correctly.

*Juice might be leaking if you do not place the silicone correctly. *Juice may leak if you do not assemble the silicone parts properly.

1. Disassemble

<Silicone Wiper Blade> Hold the Tail portion (2 in the drawing) of the silicone blade and push upward to the middle of the blade slot, then pull outward.

	Hold the Head portion (1 in the drawing) of
	the silicone blade and slide downward to the
	<Silicone brush>
	middle of the blade slot, then pull outward.
	Face down the tail of silicone brush and put it in
	2. Assemble
	like the picture next to it.
	Insert the Head portion into the blade slot
	in the middle of the bracket, slide the Head
tail	upward. Insert the Tail portion into the blade
	slot in the middle of the bracket, slide the Tail
	downward.

<Pressure Plug of Auger Housing>

After washing, put the Pressure Plug in correctly as shown in the picture.

<Silicone Extraction>

After washing, put the silicone in correctly with arrow in the picture.

<Sealing Ring of the Auger Housing>

Sealing Ring can be easily disassembled by pushing<SiliconefromRing>the bottom side of the Auger Housing (smaller silicone ring) for easy clean- Silicone ring can be washed. Put the silicone ring ing. After it is thoroughly dried, put the sealing back to the place properly.

ring properly back in its place. Push the sealing

ring (with the larger side facing up) back in Bigger silicone side, face up and place it place from the inside of the Auger Housing. correctly.

›