200712159 93-2768 RV Series Inverter-Charger Owner’s Manual_Eng.qxd 2/29/2008 1:55 PM Page 8

Battery Selection (continued)

•STEP 3: Estimate Battery Amp-Hours Required (for operation unsupported by the alternator)

Multiply the DC amps required (from step 2, above) by the number of hours you estimate you will operate your equipment exclusively from battery power before you have to recharge your batteries with utility- or generator-supplied AC power. Compensate for inefficiency by multiplying this number by 1.2. This will give you a rough estimate of how many amp-hours of battery power (from one or several batteries) you should connect to your Inverter/Charger.

45 DC Amps × 5 Hrs. Runtime

× 1.2 Inefficiency Rating = 270 Amp-Hours

NOTE! Battery amp-hour ratings are usually given for a 20-hour discharge rate. Actual amp-hour capacities are less when batteries are discharged at faster rates. For example, batteries discharged in 55 minutes provide only 50% of their listed amp-hour ratings, while batteries discharged in 9 minutes provide as little as 30% of their amp-hour ratings.

•STEP 4: Estimate Battery Recharge Required, Given Your Application You must allow your batteries to recharge long enough to replace the charge lost during inverter operation or else you will eventually run down your batteries. To estimate the minimum amount of time you need to recharge your batteries given your application, divide your required battery amp-hours (from step 3, above) by your Inverter/Charger’s rated charging amps (see Specifications section).

270 Amp-Hours ÷ 55 Amps

Inverter/Charger Rating = 5 Hours Recharge

NOTE! For Tripp Lite Inverter/Chargers providing 1000 watts or less of continuous AC power, a full-size battery will normally allow sufficient power for many applications before recharging is necessary. For mobile applications, if a single battery is continuously fed by an alternator at high idle or faster, then recharging from utility or generator power may not be necessary. For Tripp Lite Inverter/Chargers over 1000 watts used in mobile applications, Tripp Lite recommends you use at least two batteries, if possible fed by a heavy-duty alternator anytime the vehicle is running. Tripp Lite Inverter/Chargers will provide adequate power for ordinary usage within limited times without the assistance of utility or generator power. However, when operating extremely heavy electrical loads at their peak in the absence of utility power, you may wish to “assist your batteries” by running an auxiliary generator or vehicle engine, and doing so at faster than normal idling.

Mounting

WARNING! Mount your Inverter/Charger BEFORE DC battery and AC power connection. Failure to follow these instructions may lead to personal injury and/or damage to the Inverter/Charger and connected systems.

Tripp Lite manufactures a variety of different Inverter/Chargers with a variety of different mounting options for use in vehicular or non-vehicular applications. Tripp Lite recommends permanent mounting of your Inverter/Charger in any of the configurations illustrated below. User must supply mounting hardware and is responsible for determining if the hardware and mounting surface are suitable to support the weight of the Inverter/Charger. Contact Tripp Lite if you require further assistance in mounting your Inverter/Charger.

Vehicular and Non-Vehicular Horizontal Mount

(750 & 1250 models only)

AUsing the measurements from the diagram, install two user-supplied ¼" (6 mm) fasteners into a rigid horizontal surface, leaving the heads slightly raised. B Slide the Inverter/Charger back over the fasteners to engage the mounting slots molded on the bottom of the Inverter/Charger cabinet. C Install and tighten two user-supplied ¼" (6 mm) fasteners into the mounting feet molded on the front of the Inverter/Charger cabinet.

C

A

4.5 in.

(11.4 cm)

6.75 in. B

(17.1 cm)

 

 

 

 

6.75 in.

7.87 in.

 

 

 

(17.1 cm)

 

 

 

 

 

 

 

 

(20 cm)

 

 

 

 

The polycarbonate cabinet and mounting feet of your Inverter/Charger are durable enough to allow for wall mounting as well (if your vehi- cle compartment requires this configuration). For wall mounting, the control panel of the Inverter/Charger must face to the side and not up or down.

Allow 2" minimum front and rear clearance for adequate ventilation.

8

Page 7 Page 9
Page 8
Image 8
Tripp Lite 200712159 93-2768 RV owner manual Mounting, Vehicular and Non-Vehicular Horizontal Mount
Page 7 Page 9

200712159 93-2768 RV specifications

The Tripp Lite 200712159 93-2768 RV is a versatile and reliable power solution, designed for both recreational vehicles and various portable applications. Known for its robust performance and sturdy construction, this device offers a multitude of features that make it an essential component for adventurers and outdoor enthusiasts.

One of the standout features of the Tripp Lite 200712159 is its exceptional output capacity. With the ability to handle significant load requirements, it ensures that all your essential devices can be powered simultaneously without compromising performance. This capability is particularly beneficial for RV users who rely on multiple devices, such as refrigerators, laptops, and entertainment systems, while on the road.

The device also boasts advanced surge protection technology, safeguarding connected equipment from transient voltage spikes, which can occur due to lightning strikes or power surges. This feature provides peace of mind, particularly when traveling through areas with unstable power sources. In addition, the unit is designed with rugged durability in mind, featuring a weather-resistant casing that protects it from the elements. This characteristic makes it perfect for outdoor use, where exposure to moisture and changing temperatures can be a concern.

The Tripp Lite 200712159 is also incredibly user-friendly. It includes an intuitive interface with LED indicators, allowing users to easily monitor power status and load capacity. This interface helps ensure users can operate the device efficiently, reducing the risk of overload situations. Furthermore, the compact design of the unit makes it easy to transport and store, which is a vital consideration for RV travelers who often have limited space.

A notable characteristic of this power solution is its compatibility with a wide range of devices. From laptops and smartphones to larger appliances, the Tripp Lite 200712159 can accommodate various power needs, making it an ideal choice for camping trips, tailgating events, and more.

In conclusion, the Tripp Lite 200712159 93-2768 RV stands out as a highly functional power supply that combines robustness, safety features, and user-centric design. Its impressive versatility and ability to handle substantial demands make it a must-have for anyone looking to enhance their outdoor experiences or streamline their RV adventures. With this power solution at your disposal, you can confidently enjoy all your electronic devices, no matter where the road takes you.
Top Page Image Contents