Tripp Lite RV Series Mounting

10R

Mounting

WARNING! Mount your Inverter/Charger BEFORE DC battery and AC power

connection. Failure to follow these instructions may lead to personal injury

and/or damage to the Inverter/Charger and connected systems.

Tripp Lite manufactures a variety of different Inverter/Chargers with a variety of different mounting options for use in vehicular or non-vehicular

applications. Tripp Lite recommends permanent mounting of your Inverter/Charger in any of the configurations illustrated below. User must

supply mounting hardware and is responsible for determining if the hardware and mounting surface are suitable to support the weight of the

Inverter/Charger. Contact Tripp Lite if you require further assistance in mounting your Inverter/Charger.

750 & 1250 Models Only

Whether mounted horizontally or vertically, the

Inverter must be located in an enclosed compartment,

shielded from outside weather conditions.

Using the measurements from the diagram, install two user-sup-

plied ¼" (6 mm) fasteners into a rigid horizontal surface, leaving

the heads slightly raised. Slide the Inverter/Charger back over

the fasteners to engage the mounting slots molded on the bottom of

theInverter/Charger cabinet. Install and tighten two user-sup-

plied ¼" (6 mm) fasteners into the mounting feet molded on the

front of the Inverter/Charger cabinet.

The polycarbonate cabinet and mounting feet of your

Inverter/Charger are durable enough to allow for vertical mount-

ing as well, if your vehicle compartment requires this configura-

tion. For vertical mounting, the control panel of the

Inverter/Charger should face up.

All Models Except 750 & 1250 Models

Note: When operating an RV2012UL marine model

in a marine application, refer to the accompanying

marine owners' manual addendum.

Whether mounted horizontally or vertically, the

Inverter must be located in an enclosed compartment,

shielded from outside weather conditions.

Using the measurements from the diagram, install two user-sup-

plied ¼" (6 mm) fasteners into a rigid horizontal surface, leaving

the heads slightly raised. Slide the Inverter/Charger forward

over the fasteners to engage the mounting feet molded on the

front of the Inverter/Charger cabinet. Install and tighten

additional user-supplied ¼" (6 mm) fasteners into the mounting

feet molded on the rear and sides of the Inverter/Charger

cabinet*. The rear feet extend beyond the unit’s cabinet to

provide for adequate ventilation space behind the cooling fan(s);

they should not be removed.

The polycarbonate cabinet and mounting feet of your

Inverter/Charger are durable enough to allow for vertical mount-

ing as well, if your vehicle compartment requires this configura-

tion. For vertical mounting, the control panel of the

Inverter/Charger should face up.

Allow 2" minimum front and rear clearance for adequate ventilation.

5.87 in.

(14.91 cm.)

1.64 in.

(4.15 cm.)

5.87 in.

(14.91 cm.

)

5.57 in.

(14.16 cm.)

5.57 in.

(14.16 cm.)

9.59 in.

(24.35 cm.)

9.59 in.

(24.35 cm.)

6.75 in.

(17.1 cm)

7.87 in.

(20 cm)

6.75 in.

(17.1 cm)

4.5 in.

(11.4 cm)

Note: RVmodel cabinets may have different front panel features, but all mount as per the figure above.

* All models include front and rear mounting feet. Select

models include side mounting feet.

Allow 2" minimum front and rear

clearance for adequate ventilation.

200605181 RV Series Inverter-Charger Owner’s Manual.qxd 8/24/2006 2:35 PM Page 10