Tripp Lite TMU Series owner manual Feature Identification, Move-Ups

Feature Identification

Identify the premium features on your specific model and quickly locate instructions on how to maximize their use.

1 Configuration DIP Switches: optimize UPS System operation depending on your application. See Configuration section for setting instructions.

2Operating Mode Switch: controls UPS System operation. See Operation section for setting instructions.

10 Main Ground Lug: properly grounds the UPS System to earth ground. See Configuration section for instructions.

11Multi-Speed Cooling Fan: quiet, efficient fan prolongs equipment service life.

12Hardwire AC Input/Output Cover Plate

3	“LINE”, “INVERT”, “LOAD” LEDs: show whether the UPS		Battery Temperature Sensing Connector (not on TMU612
		13
	System is operating from AC line power or DC battery power.
			models): prolongs battery life by adjusting charge based on bat-
	It also warns you if the connected equipment load is too high. See
			tery temperature. Use with included cable. See Configuration
	Operation section for instructions on reading the indicator lights.
			section for details.
	“BATTVOLT/CHRGCURR” LEDs: these three lights will turn
4		14	Low Battery Relay (not on TMU612 models): when battery

ON in several sequences to show two separate operational condi-	reaches low voltage, this relay can signal traffic controller to go
tions depending on the position of the Operating Mode Switch. See
	to flashing red mode or to send low battery alert to your control
Operation section for instructions on reading indicator lights.
	center. See Configuration section for details.

5DC Power Terminals: connect to your battery terminals. See

	Battery Connection section for instructions.	Optional Features for alternate uses of Tripp Lite Traffic
6	AC Receptacles (not on hardwire models): allow you to connect	MOVE-UPS

equipment that would normally be plugged into a utility outlet.

	AC	Input Cord (not on hardwire models): connects the		Tripp Lite’s TMU UPS models are versatile and can be used in
7
				mobile applications as well, such as running AC power tools in
	UPS	System to any source of utility- or generator-supplied
				municipal maintenance trucks or police command vehicles.
	AC power. SeeAC Input/Output Connection section for instructions.
				The features listed below are available for such alternate uses.
	Hardwire AC Input/Output Terminals (not on corded
8
	models): securely connect the UPS System to electrical system		15	Remote Control Module Connector: designed only for mobile
	input and equipment output. See AC Input/Output Connection			applications, this connector allows remote control from up to 50
	section for instructions.			feet away with optional module, sold separately. If required,
	Resettable Circuit Breaker: protect your UPS System against			contact Tripp Lite for further information.
9
	damage due to overload. See Operation section for resetting		16	Load Sense Dial (not on TMU612 models): designed only for
	instructions.			mobile applications, this dial sets the low load level at which the
				UPS System’s inverter automatically shuts down. To guard
				against inadvertent inverter shutdown, Tripp Lite recommends
				you leave the dial in its factory default setting (fully clockwise).
				If required, contact Tripp Lite for further information.

11 1* 4 15 3 2 16 †

13† Side or Rear Mounted, Not Shown

14† Side or Rear Mounted, Not Shown

9	11	1	4	15	3	2	16
6							13	Side Mounted,
								Not Shown
							14	Side Mounted,
								Not Shown

				“FOR USE WITH COPPER WIRE ONLY”			9
	5	7	10**	HOT	IN
Front View (Corded Models)				NEUTRAL		IN
* 612 models have only one set of DIP Switches. ** Select models include front-mounted ground lug. † Available on all models except 612 models.
				GROUND		IN
				GROUND		OUT
				HOT	OUT
				NEUTRAL		OUT
			5	8	12
10			Front View (Hardwire Models)

Rear View (Hardwire Models and Select Corded Models)

4T