Operation

Starting the Engine

Disconnect all electrical loads from the generator. Use the following start instructions:

1. Make sure unit is on a level surface.

IMPORTANT: Failure to start and operate the unit on a level surface will cause the unit not to start or shut down during operation.

2.Turn fuel valve to “On” position. Fuel valve handle should be vertical (pointing toward ground) for fuel to flow.

3. Push choke lever to “Choke” position.

4. Push engine rocker switch to “On”.

5.Grasp recoil handle and pull slowly until slight resistance is felt. Then pull handle rapidly to overcome compression, prevent kickback, and start engine.

WARNING

Starter cord kickback (rapid retraction) can result in bodily injury. Kickback will pull hand and arm toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains could result.

When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.

NEVER start or stop engine with electrical devices plugged in and turned on.

IMPORTANT: If excessive fuel is present in the air/fuel mixture causing a “flooded” condition, move the choke lever to “Run” ( ) position and pull the handle repeatedly until the engine starts.

6.Move choke lever to “Run” ( ) position a short distance at a time over several seconds in warm weather or minutes in cold weather. Let engine run smoothly before each change. Operate with choke in “Run” position.

WARNING

Contact with muffler area can result in serious burns.

Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

DO NOT touch hot parts and AVOID hot exhaust gases.

Allow equipment to cool before touching.

Keep at least 5 feet (1.5 m) of clearance on all sides of generator including overhead.

Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public Property require equipment powered by an internal combustion engine to have a spark arrester, maintained in effective working order, complying to USDA Forest service standard 5100-1C or later revision. In the State of California a spark arrester is required under section 4442 of the California Public resources code. Other states may have similar laws.

NOTE: If the engine starts after 3 pulls but fails to run, or if the unit shuts down during operation, make sure the unit is on a level surface and check for the proper oil level in the crankcase. This unit may be equipped with a low oil protection device.

10

troybilt.com

Page 12
Image 12
Troy-Bilt 30331 manual Operation, Starting the Engine

30331 specifications

The Troy-Bilt 30331 is a powerhouse in the world of lawn care, combining advanced technology with user-friendly features to enhance the mowing experience. Designed for homeowners who prioritize efficiency and performance, this lawn mower is packed with features that make lawn maintenance easier and more enjoyable.

One of the standout characteristics of the Troy-Bilt 30331 is its powerful 382cc OHV engine. This engine delivers ample power and torque, making it efficient at tackling tough grass and uneven terrain. The engine is designed for durability and reliability, ensuring that homeowners can depend on it for years of high-quality lawn care.

A key feature of the Troy-Bilt 30331 is its 21-inch cutting deck, which provides a perfect balance between agility and coverage. The cutting deck is equipped with an adjustable height setting, allowing users to choose their desired grass length, ensuring that lawns look pristine after every mow. The mower also utilizes a tri-action system that allows for superior mulching, bagging, and side discharge functionalities. This versatility not only enhances the aesthetics of your lawn but also contributes to overall lawn health.

User comfort and convenience are top priorities in the design of the Troy-Bilt 30331. It comes with ergonomic handles that reduce fatigue during extended use, and its self-propulsion feature allows users to maintain control while effortlessly navigating various terrains. This feature is especially beneficial for those with larger yards or hilly landscapes.

Another innovative technology incorporated in the Troy-Bilt 30331 is its easy-start system. This feature simplifies the starting process, allowing users to get to work quickly without the hassle of traditional pull-start methods. The mower also includes large rear wheels that provide excellent traction and maneuverability, making it easier to handle tight corners and navigate around obstacles.

Maintenance of the Troy-Bilt 30331 is straightforward, thanks to its accessible design. The cutting blade can be easily removed and sharpened or replaced, and the engine is equipped with a quick oil-change system to keep it running smoothly. With proper care, users can expect longevity and performance from this reliable lawn mower.

In summary, the Troy-Bilt 30331 is an impressive lawn mower that excels in performance, versatility, and user comfort. With its powerful engine, adjustable cutting deck, ergonomic design, and convenient features, it stands out as an excellent choice for homeowners seeking a dependable and efficient mowing solution.