Add Engine Oil

1.Place generator on a flat, level surface.

2.Clean area around oil fill and remove yellow oil fill cap.

NOTE: See the section Oil to review oil recommendations. Verify provided oil bottle is correct viscosity for current ambient temperature.

3.Using oil funnel (optional), slowly pour contents of provided oil bottle into oil fill opening.

NOTICE

Improper treatment of generator can damage it and shorten its life.

DO NOT attempt to crank or start the engine before it has been properly serviced with the recommended oil. This may result in an engine failure.

4.Replace oil fill cap and fully tighten.

Add Fuel

Fuel must meet these requirements:

Clean, fresh, unleaded gasoline.

A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.

Gasoline with up to 10% ethanol (gasohol) or up to 15% MTBE (methyl tertiary butyl ether) is acceptable.

NOTICE

Avoid generator damage.

Failure to follow Operator’s Manual for fuel recommendations voids warranty.

DO NOT use unapproved gasoline such as E85.

DO NOT mix oil in gasoline.

DO NOT modify engine to run on alternate fuels.

To protect the fuel system from gum formation, mix in a fuel stabilizer when adding fuel. See Storage. All fuel is not the same. If you experience starting or performance problems after using fuel, switch to a different fuel provider or change

brands. This engine is certified to operate on gasoline. The

emission control system for this engine is EM (Engine Modifications).

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

WHEN ADDING FUEL

Turn generator OFF and let it cool at least 2 minutes before removing fuel cap. Loosen cap slowly to relieve pressure in tank.

Fill fuel tank outdoors.

DO NOT overfill tank. Allow space for fuel expansion.

If fuel spills, wait until it evaporates before starting engine.

Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources.

DO NOT light a cigarette or smoke.

1.Clean area around fuel fill cap, remove cap.

2.Slowly add unleaded gasoline (A) to fuel tank (B). Be careful not to overfill. Allow about 1.5" (4 cm) of tank space (C) for fuel expansion.

B

C

A

3.Install fuel cap and let any spilled fuel evaporate before starting engine.

High Altitude

At higher altitudes (over 5,000 feet), 85 octane/85 AKI

(89 RON) gasoline is recommended. High-altitude use may require a carburetor jet kit to improve performance and decrease fuel consumption. See an authorized service center for more information.

6

troybilt.com

Page 8
Image 8
Troy-Bilt 30331 manual Add Engine Oil, Add Fuel, Replace oil fill cap and fully tighten, Fuel must meet these requirements

30331 specifications

The Troy-Bilt 30331 is a powerhouse in the world of lawn care, combining advanced technology with user-friendly features to enhance the mowing experience. Designed for homeowners who prioritize efficiency and performance, this lawn mower is packed with features that make lawn maintenance easier and more enjoyable.

One of the standout characteristics of the Troy-Bilt 30331 is its powerful 382cc OHV engine. This engine delivers ample power and torque, making it efficient at tackling tough grass and uneven terrain. The engine is designed for durability and reliability, ensuring that homeowners can depend on it for years of high-quality lawn care.

A key feature of the Troy-Bilt 30331 is its 21-inch cutting deck, which provides a perfect balance between agility and coverage. The cutting deck is equipped with an adjustable height setting, allowing users to choose their desired grass length, ensuring that lawns look pristine after every mow. The mower also utilizes a tri-action system that allows for superior mulching, bagging, and side discharge functionalities. This versatility not only enhances the aesthetics of your lawn but also contributes to overall lawn health.

User comfort and convenience are top priorities in the design of the Troy-Bilt 30331. It comes with ergonomic handles that reduce fatigue during extended use, and its self-propulsion feature allows users to maintain control while effortlessly navigating various terrains. This feature is especially beneficial for those with larger yards or hilly landscapes.

Another innovative technology incorporated in the Troy-Bilt 30331 is its easy-start system. This feature simplifies the starting process, allowing users to get to work quickly without the hassle of traditional pull-start methods. The mower also includes large rear wheels that provide excellent traction and maneuverability, making it easier to handle tight corners and navigate around obstacles.

Maintenance of the Troy-Bilt 30331 is straightforward, thanks to its accessible design. The cutting blade can be easily removed and sharpened or replaced, and the engine is equipped with a quick oil-change system to keep it running smoothly. With proper care, users can expect longevity and performance from this reliable lawn mower.

In summary, the Troy-Bilt 30331 is an impressive lawn mower that excels in performance, versatility, and user comfort. With its powerful engine, adjustable cutting deck, ergonomic design, and convenient features, it stands out as an excellent choice for homeowners seeking a dependable and efficient mowing solution.