3

Setup and

Adjustment

NOTE: This Operator’s Manual covers several models. Lawn Mower features vary by model. Not all features discussed (or engines pictured) in this manual are applicable to all Lawn Mower models.

NOTE: Stand behind the mower as if you were going to operate it. Your right hand corresponds to the right side of the mower; your left hand corresponds to the left side of the mower.

NOTE: Your mower

A

B

Figure 3-1: Unfold handle and tighten hardware.

 

Hardware Pack

B

Wing Nuts (2) Carriage Bolts (2)

A

Figure 3-2: Secure lower handle to mounting brackets.

IMPORTANT: This unit is shipped without gasoline or oil in the engine. Fill up gasoline and oil as instructed in the accompanying engine manual BEFORE operat- ing your mower.

1.Remove any packing material which may be between upper and lower handles.

a.Pull up and back on upper handle as shown in Figure 3-1. Make certain the lower handle is seated securely into the handle mounting brackets. Do not crimp cable while lifting the handle up.

b.Tighten star knobs securing upper handle to lower handle. See Figure 3-1. Make sure that each carriage bolt is seated properly in the handle.

2.Locate the hairpin clip on the weld pin on each side lower handle.

a.Remove hairpin clip from this hole. Using a pair of pliers, insert hairpin clip into the hole on pin closest to the bracket. See Figure 3-2. Repeat on other side.

b.Insert a carriage bolt from the hardware pack into the upper hole on the handle mounting bracket as shown in Figure 3-2. Secure with one plastic wing nut, also included in the hardware pack. Repeat on other side.

3.The rope guide is attached to the right side of the upper handle. Loosen the wing nut which secures the rope guide. See Figure 3-3.

a.Hold blade control against upper handle.

b.Pull starter rope out of the engine. Release blade control handle.

c.Slip starter rope into rope guide.

d.Tighten wing nut.

4.Insert post on cable ties into holes provided on the lower handle. Pull cable tie tight and trim excess. See Figure 3-4.

is shipped with the handle in the higher height position.

NOTE: Each end of the lower handle must be placed in the same relative position.

IMPORTANT This unit is shipped without gasoline or oil in the engine. Fill up gasoline and oil as instructed in the accompanying engine manual BEFORE operating your mower.

A

B

D

C

Figure 3-3: Pull recoil starter through rope guide and tighten.

Figure 3-4: Secure cable to handle using cable ties.



Page 5 Page 7
Page 6
Image 6
Troy-Bilt 420 warranty Setup Adjustment, Unfold handle and tighten hardware
Page 5 Page 7

420 specifications

The Troy-Bilt 420 is an impressive addition to the lineup of outdoor power equipment, specifically designed for homeowners seeking exceptional performance in lawn care and maintenance. This Troy-Bilt product stands out due to its robust features, advanced technologies, and user-friendly characteristics, making it a reliable choice for gardening enthusiasts.

One of the main features of the Troy-Bilt 420 is its powerful engine. Equipped with a 420cc engine, it delivers ample power for a variety of tasks, including tilling, mowing, and snow removal. This high-performance engine is designed to provide optimal torque and efficiency, ensuring that you can tackle even the toughest jobs with ease.

Another key characteristic of the Troy-Bilt 420 is its innovative tilling capability. The tiller boasts a wide tilling width of 24 inches, enabling you to cover larger areas in a shorter amount of time. Additionally, it features adjustable tilling depths, allowing users to customize their tilling experience based on the specific needs of their soil and garden. This versatility is essential for achieving effective soil aeration and preparation for planting.

In terms of technology, the Troy-Bilt 420 features a cushioned grip handle for enhanced comfort during extended use. This ergonomic design reduces muscle fatigue and allows for better control of the tiller, ensuring precision in your gardening tasks. The tiller also incorporates a self-propelled drive system, which not only enhances ease of use but also boosts productivity. This means you can focus on your gardening without having to struggle to push or pull the equipment.

The durability of the Troy-Bilt 420 is evident in its construction. Built with high-quality materials, it is designed to withstand the rigors of outdoor use, providing longevity and reliability. Its sturdy design ensures stability during operation, while the heavy-duty tines offer efficient tilling performance.

Finally, maintenance of the Troy-Bilt 420 is straightforward, thanks to accessible components and clear instructions. This design consideration allows homeowners to easily perform routine checks and servicing, which is crucial to keep the equipment running at peak performance.

Overall, the Troy-Bilt 420 combines power, versatility, and user-friendly features, making it an ideal choice for anyone looking to enhance their lawn care routine. Whether you're an experienced gardener or a novice, the Troy-Bilt 420 proves to be a dependable tool that can help you achieve a thriving garden and a well-maintained landscape.
Top Page Image Contents