Troy-Bilt MXZ-4A36NA, MXZ-3A30NA installation manual Outdoor Unit Installation, Installing The Unit

Models: MXZ-4A36NA MXZ-3A30NA

1 20
Download 20 pages 15.09 Kb
Page 5
Image 5
2. OUTDOOR UNIT INSTALLATION

2. OUTDOOR UNIT INSTALLATION

2-1. INSTALLING THE UNIT

Be sure to fix the unit’s legs with bolts when installing it.

Be sure to install the unit firmly to ensure that it does not fall by an earthquake or a gust.

Refer to the figure in the right for concrete foundation.

Do not use the drain socket and the drain cap in the cold region.

Drain may freeze and it makes the fan stop.

Fix here with

M10 bolts.

Make the setting depth deeper.

Make with wider.

25 (1) or less

Anchor leg

Anchor both length

500

(19.69)

330 (13.00)

Anchor both pitch

[Unit: mm (inch)]

2-2. CONNECTING WIRES FOR OUTDOOR UNIT

Be sure to use special circuits for room air conditioner.

Wiring work should be based on applicable technical standards.

Wiring connections should be made following the diagram.

Screws should be tightened so they won’t loosen.

 

 

 

ELECTRICAL SPECIFICATIONS

 

 

INDOOR UNIT

 

MSZ-A09NA

 

MSZ-A12NA

 

MSZ-A15NA

Power supply (V, PHASE, Hz)

 

 

 

 

 

208/230, 1, 60

Min. Circuit Ampacity (A)

 

1.0

 

1.0

 

1.0

Fan motor (F.L.A)

 

0.76

 

0.76

 

0.76

OUTDOOR UNIT

 

 

 

 

 

 

 

 

 

MXZ-3A30NA

 

 

Power supply (V, PHASE, Hz)

 

 

 

 

 

208/230, 1, 60

Max. Fuse size (time delay) (A)

 

 

20

 

 

 

Min. Circuit Ampacity (A)

 

 

15

 

 

 

Fan motor (F.L.A)

 

 

0.93

 

 

 

Compressor

(R.L.A)

 

11

 

 

 

(L.R.A)

 

15

 

 

 

 

 

 

 

 

Control voltage

 

Indoor unit-Remote controller : (Wireless)

 

 

 

Indoor unit-Outdoor unit : DC12-24V

 

 

 

 

 

 

1) Remove the service panel.

2) Fix the conduit connector to conduit cover with lock nut then secure it against unit with screws.

3) Fix the conduit cover to the outdoor unit then secure it with screws.

4) Connect power supply and indoor/outdoor connecting wire to the terminal block.

(Leave some slack in wires to allow easier servicing.)

5) Close the service panel securely. Make sure that 3-2. PIPE CONNECTION is completed.

Connecting order

 

 

 

 

Power supply

• Connect the terminal block in order,

 

 

 

 

 

 

 

from the A, B and C unit side.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MSZ-A17NA

MSZ-A24NA

1.01.0

0.760.76

MXZ-4A36NA

20

19

0.93

14.4

15

Terminal block for power supply

Service panel

4A36NA

Terminal block for indoor/outdoor unit

Page 5
Image 5
Troy-Bilt MXZ-4A36NA, MXZ-3A30NA Outdoor Unit Installation, Installing The Unit, Connecting Wires For Outdoor Unit