Manuals / Tyan Computer / Computer Equipment / Network Card

Tyan Computer B2881 manual Disconnect all fan power cables

Models: B2881

1 82

Download 82 pages 32.4 Kb

<>

Install Motherboard Block Diagram System Fan Monitoring Signal Jumpers & Connectors Function Environment Temperature Precautions Safety Power Cable Data Cable Features

Page 52

4. Disconnect all fan power cables.

44	Chapter 3: Replacing Pre-Installed Components

Page 51 Page 53

Image 52

Tyan Computer B2881 manual Disconnect all fan power cables

Page 51 Page 53

Related pages All Power page Auxiliary Power Loads for Lincoln Electric SVM175-A Power maitinimo kodas, kuris bus nustatytas gaminyje NAK for Samsung LH22DBDPLGC/EN BenQ LCD Monitor Monitor Base Quick Start Guide CD-ROM Power Cord for BenQ G700A Do not damage the power cord for Sanyo VPC-J1EX Power Cord for Samsung VCC8680V3K/XEE POWER S/W ON / OFF O for Samsung 400CXn 2253LW PowerSaver for Samsung LS22AQWJFVMXSV Power cords and power adapters for IBM 8183 Power Saving Function for Samsung LS22A450DWT/EN Power Switch for Actiontec electronic MI424-WR Where can I find the official Chicago Electric power tools manuals?

Contents

Transport GT24 B2881 Service Engineer’s Manual Page Preface Federal Communications Commission FCC Conventions Safety Information Table of Contents Technical Support Overview About the Transport GT24 B2881 Product Models B2881G24S4H B2881G24U4H B2881G24S4-LCModel HDD Bays Hot-Swap Support Backplane Features Environment Temperature Power SupplyRegulatory Unpacking FDD Kit Rail Kit CD-ROM Accessory Kit for B2881G24S4-LC only System Front View B2881G24S4-LC About the ProductB2881G24IU4H/B2881G24S4H System Rear View LED Definition Front Panel Rear I/O LED System Internal View B2881G24S4-LC FAN1 109 B2881G24S4H B2881G24U4H 109 Motherboard Layout Jumpers & Connectors Function Motherboard Block Diagram Work Area Before You BeginTools Precautions Rack Mounting Installing the Server in a RackRack mounting kit Installing the Inner Rails to Chassis Installing Outer Rails to the Rack Locate the front and rear brackets Remember to add washer Front Side Rear Side Rackmounting the Server Setting Up Installing Motherboard Components Removing the Chassis Cover Installing the CPU, Heatsink and Air Duct Setting Up Installing the Memory Installing a PCI-X Card Setting Up Installing the Hard Drive for B2881G24S4-LC Setting Up Installing the Hard Drive for B2881G24S4H/U4H Setting Up Installing the Slim FDD Option Connect the other side to the connector on motherboard Installing the CD-ROM or DVD-ROM for B2881G24S4-LC only Power Cable Data Cable Replacing Pre-Installed Components Introduction Precautions Disassembly Flowchart Following flowchart outlines the disassembly procedure Removing the Cover Main Power EPS 12V Power Disconnecting All Motherboard CablesReplacing Motherboard Components Disconnect all fan power cables Removing the Motherboard Replacing the LED Control Board Replacing Pre-Installed Components Replacing the M1012 Adapter Board 1 M1012 Adapter Board Features J3 LAN/ID LED 2 M1012 Adapter Board Connector Pin Definition FAN Signal Related Connector Pin Definition GND FAN1TACH FAN2TACH FAN3TACH KEY PIN FAN312VPWM FAN3TACH GND FAN4TACH FAN412VPWM FAN912VPWM FAN9TACH GND FAN10TACH System Fan Layout System Fan Speed Control Signal System Fan Monitoring Signal Replacing the Sata or Scsi Backplane Replacing Pre-Installed Components ATA Backplane M1204 Features Replacing Pre-Installed Components M1204 HDD Access LED Connector Pin Definition Scsi Backplane M1205 Features Replacing Pre-Installed Components M1205 HDD Start-Mode & ID Selection Switch CaseMotor Spin Func Tion ID Sequence Left to right in front view Replacing the Power Supply B2881 Advanced/Hardware Health Information S2881 Advanced/Hardware Health Information Table of Differences S2881 B2881 Appendix II Cable Connection Tables Power Supply Cable FDD Related Cable Option Technical Support Help Resources Returning Merchandise for Service

Top Page Image Contents