10-2. Re-registering Handsets
When you first put your handsets into the base, they are registered to the base so they can communicate with the base. There may be some times when you have to
•When you want to change the
•When there is a power failure that lasts more than one hour.
•If a handset's battery is completely discharged. (The handset must be recharged for 15 - 20 hours before re- registering to the base.)
•Any time you experience difficulty connecting to the base to make or receive calls.
To re-register handsets:
1) | Pick up the handset from the base. Press and hold [find hs] on the base. |
2) | While holding [find hs], place the handset in the base. The charge/in use LED on the base begins to |
| flash, indicating the base is registering the handset. Wait for at least five seconds. |
3)Pick up the handset from the base and press [TALK/flash]. If the display shows TALK, the handset is registered. If not, place the handset in the base to try again.
4)Press [END].
5)One by one, place each handset in the base and wait for at least five seconds. (You don't need to hold [find hs] this time.) Repeat steps 3 - 4.
10-3. Changing the Handset-to-base Code
The
If any one of handsets can't communicate with the base, place that handset in the base cradle to reset the code. Wait at least five seconds, then pick up the handset and press [TALK/flash]. If the display shows TALK, the code is reset.
If the code does not reset or if you suspect another cordless telephone might be using the same code (a rare situation), you can change the
10-4. Traveling Out of Range
During a call, as you begin to move your handset too far from your base noise increases. If you pass the range limits of the base, your call will terminate within one minute.
10-5. Liquid Damage
Moisture and liquid can damage your cordless phone.
•If the handset or base is exposed to moisture or liquid, but only the exterior plastic housing is affected, wipe off the liquid, and use as normal.
•If moisture or liquid has entered the plastic housing (i.e. liquid can be heard in the phone or liquid has entered the handset battery compartment or vent openings on the base), follow the steps below:
| Handset |
| Base |
|
|
|
|
1) | Remove the battery cover and leave it off for ventilation. | 1) | Disconnect the AC adapter |
2) | Disconnect the battery pack. Leave the battery cover off and the |
| from the base, cutting off |
| battery pack disconnected for at least three days. |
| electrical power. |
3) | Once the handset is completely dry, reconnect the battery pack and | 2) | Disconnect the telephone cord |
| the battery cover. |
| from the base. |
4) | Recharge the handset's battery pack for 15 to 20 hours before using. | 3) | Let dry for at least three days. |
|
|
|
|
IMPORTANT:
You must unplug the telephone line while recharging the battery pack to avoid charge interruption.
CAUTION!
DO NOT use a microwave oven to speed up the drying process. This will cause permanent damage to the handset, base and the microwave oven. After following these steps, if your cordless telephone does not work, please call our Customer Service Hotline. See back cover page for contact information.
10-6. Specifications
The phone complies with FCC Parts 15 and 68.
Operating temperature | 0°C to +50°C (+32°F to +122°F) |
| ||
|
| For the base | For the charging cradle | |
AC Adapter | Part number | |||
Input Voltage | 120V AC 60Hz | 120V AC 60Hz | ||
| ||||
| Output Voltage | 9V DC 350mA | 9V DC 210mA | |
Battery | Part number |
| ||
Capacity | 600mAh, 3.6V |
| ||
|
| |||
Frequency | 921.103102 – 923.787761 MHz |
| ||
5,856.533347 – 5,863.692437MHz |
| |||
|
| |||
Note: To avoid damage to the phone, use only Uniden
10-7. Power Failure Operation
During the period that the power is off, you will not be able to make or receive calls with the telephone.
10-8. Battery Information
Average battery life
With average use, your handset battery provides approximately six hours of talk time and approximately seven days of standby time. You can achieve optimum battery life and performance by returning the handset to the cradle after each use. When your handset is left off of the cradle, the battery will gradually discharge even if the handset is not being used. The actual talk time duration will be reduced in proportion to the amount of time the handset is off the cradle.
Low battery alert
When the battery pack is very low and needs to be charged, the phone is programmed to eliminate functions in order to save power. If the phone is not in use, LOW BATTERY CHARGE HANDSET appears on the LCD, and none of the keys will operate. During a call, the handset beeps, and the LCD flashes LOW BATTERY. Complete your conversation as quickly as possible and return the handset to the cradle for charging.
Note: Information stored in the phone's memory will be retained for thirty minutes after the battery pack is removed. This includes all setup information, last number dialed, speed dial memory, and the CID list.
