Uniden EXAI 4248 Using Your Phone

USING YOUR PHONE [16]

www.uniden.com

Using Your Phone

Making and Receiving Calls

Making a call

1) Remove the handset from the base.

2) Press the talk/flash key.

3) Listen for the dial tone.

4) Dial the number.

1) Remove the handset from the base.

2) Dial the number.

3) Press the talk/flash key.

Receiving a call

1) Remove the handset from the base. (If AutoTalk is on, the phone will automatically

answer the call when you pick it up.)

2) Press the talk/flash key.

1) If the handset is off the base, press the talk/flash key, the*/tone/ key, the #/ key

or any number key. (AutoTalk is on.)

Hanging up

Press the end key or return the handset to the base.

USING YOUR PHONE

To turn on the AutoTalk

feature, see “Activating

AutoTalk” on page12.

note

EXAI7248.book Page 16 Thursday, December 14, 2006 11:57 AM

Contents

Main Contents Welc ome Feat ure s Controls and Functions Terms Used in this Manual Accessibility Installing the Phone Do the following steps: A. Choose the Best Location B. Install the Rechargeable Battery Pack into the Handset ! C. Connect the Base Unit and Charge the Handset ! D. Mount the Base Unit on a Wall Standard wall plate mounting Direct wall mounting Installing the Beltclip Headset Installation Basic Setup Activating AutoTalk Activating Caller ID on Call Waiting Entering Your Area Code Choosing the Dialing Mode Setting the Language Selecting the Ring Tone and Volume Using Your Phone Making and Receiving Calls Making a call Receiving a call Hanging up Redialing the Last Dialed Number Adjusting the Earpiece Volume Temporarily Mute Ringer Tone Dialing Switch-over Traveling Out-of-Range Selecting a Different Channel Find Handset Using Call Waiting Using the Speed Dial Memory Storing Names and Numbers in Speed Dial Memory If you make a mistake while entering a name Page Storing Caller ID Messages in Speed Dial Memory Making Calls from Speed Dial Memory To cancel speed dialing Caller ID and CIDCW (Caller ID on Call Waiting) Viewing the Caller ID Message List Deleting Information from the Caller ID List Deleting a Caller ID Message Deleting all Caller ID names/numbers Making a Call from the Caller ID List Caller ID on Call Waiting (CIDCW) The Integrated Answering Device Features Setting Up Your Answering System Answering System Settings Setting the Time Setting a Personal Security Code (PIN) Setting the Ring Time Selecting the Message Record Time Setting the Message Alert Tone Selecting the Language Setting Your Outgoing Message (Greeting) Preset message Recording a personal outgoing message (Greeting) Choosing between the two outgoing messages Setting the Base Ringer Volume Temporarily Mute the Base Ringer and Call Screen Adjusting the Speaker Volume Level Turning the Answering System On/Off Using Your Answering System hint Playing Your Messages Repeating a Message Skipping a Message Page Deleting a Message Voice M emo Recording a Conversation Handset Operation You can operate your answering system from another room using a handset. Remote Operation tip Page Turn on the Answering System Remotely Changing the Digital Security Code Note on Power Sources Low battery alert Battery replacement and handling Talk and Standby Times Cleaning the battery charging contacts General Information Troubleshooting Page Page Liquid Damage [57] PRECAUTIONS & WARRANTY EXAI7248.book Page 57 Thursday, December 14, 2006 11:57 AM www.uniden.com Precautions! Rechargeable Nickel-Cadmium Battery Warning Rechargeable Nickel-Cadmium Batteries Must Be Recycled or Disposed of Properly Important Safety Instructions SAVE THESE INSTRUCTIONS PRECAUTIONS & WARRANTY [58] EXAI7248.book Page 58 Thursday, December 14, 2006 11:57 AM www.uniden.com Radio Interference Cordless Telephone Privacy I.C. Notice TERMINAL EQUIPMENT RADIO EQUIPMENT Index Page Remote Operation Card EXAI7248.book Page 63 Thursday, December 14, 2006 11:57 AM REMOTE OPERATION CARD Phone NumberName MEMORY LOCATION MEMO