UBC61 scanner Qk 3/12/02 11:22 AM Page 6
Programming
Before the UBC61XLT can receive radio broad- casts, you must program a frequency into at least one channel before scanning, repeat this procedure for each channel you program.
Up to 80 channels may be programmed
Duplicate Frequency Alert
If you enter a frequency stored in
2
another channel, you hear a beep and the
other channel appears in the display.
Press . |
| Press E |
to start again | or | again to store the |
1.Select frequencies
2.Press • MANUAL
• SCAN | 1 | 2 | 3 | |
• MANUAL | 4 | 5 | 6 | |
SRCH SLCT | 7 | 8 | 9 | |
HOLD | CLEAR |
|
| |
• | 0 | E | ||
| ||||
|
| SKIP |
| |
LIGHT | WX | L/O | PRI |
frequency in both |
channels. |
Scanning
When you turn on the |
| SCAN |
|
power, the UBC61XLT | 88 |
| |
automatically starts in | SCAN |
|
|
the scan mode. |
|
| |
|
|
| |
|
|
|
3. Select a channel | • SCAN | 1 | 2 | |
a) Enter the | ||||
|
|
| ||
channel number | • MANUAL | 4 | 5 | |
b) Then press |
| 7 | 8 | |
• MANUAL | SRCH SLCT | |||
| HOLD | CLEAR |
| |
| • | 0 | ||
|
| |||
|
|
| SKIP | |
| LIGHT | WX | L/O |
3
6
9
E
PRI
During normal scan- ning the scanner skips unprogrammed or locked out channels.
When a transmission is received, the scanner stops on that channel. When the transmission ends, scanning
SCAN
CHANNELS
1 2 3 4 5 6 7 8 9 10
Frequency | Frequency |
locked out | not entered |
(L/O) |
|
2 000.0000 MHZ
HOLD L/O
resumes automatically after two seconds.
2 460.3750 MHZ
SCAN
4.Enter the frequency.
a)Enter the frequency number
b)Then press E
• SCAN | 1 | 2 | 3 | To stop on a channel |
during scanning, | ||||
• MANUAL | 4 | 5 | 6 | press • MANUAL |
| ||||
SRCH SLCT | 7 | 8 | 9 |
|
HOLD | CLEAR |
|
|
|
• | 0 | E |
| |
|
| |||
|
| SKIP |
|
|
LIGHT | WX | L/O | PRI |
|
• SCAN | 1 | 2 | 3 |
• MANUAL | 4 | 5 | 6 |
SRCH SLCT | 7 | 8 | 9 |
CLEAR
HOLD
• 0 E
SKIP
LIGHT WX L/O PRI
2 460.3750 MHZ
HOLD
To clear a mistake while entering the frequency, press . twice, and start over.
If the frequency entered is outside the frequency range of the scanner, a distinctive beep sounds. (See the table on page 2).
Press . |
|
|
| ERROR |
|
and go back to |
|
| 2 |
| |
step 4. |
|
|
| HOLD L/O |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| 2 460.4250 MHZ |
| ||
| HOLD |
|
|
|
To resume scanning | 1 | 2 | 3 | |
press | • SCAN | |||
• SCAN |
|
|
| |
| • MANUAL | 4 | 5 | 6 |
| SRCH SLCT | 7 | 8 | 9 |
| HOLD | CLEAR |
|
|
| • | 0 | E | |
|
| |||
|
|
| SKIP |
|
| LIGHT | WX | L/O | PRI |
| 88 | SCAN |
| |
| SCAN |
|
|
|
6
