INSTALLING YOUR ROOM HEATER ‐ continued

HORIZONTAL EXHAUST VENT INSTALLATION

1.Locate your pellet stove in a location which meets the requirements of this manual, but in an area where it does not interfere with the house framing, wiring, etc.

2.Install a non‐combustible hearth pad underneath the pellet stove. This pad should extend at least 6” (152mm) in front of the unit.

3.Place the pellet stove approximately 15” (381mm) away from the interior wall.

4.Locate the center of the exhaust pipe of your unit. This point should then be extended to the interior wall of your house. Once you have located the center point, on the interior wall, cut a 7” (175mm) diameter hole through the wall.

5.The next step is to install the wall thimble, refer to the instructions which come with the wall thimble for this step.

6.Install the appropriate length of exhaust vent pipe into the wall thimble. See step 11 when determining the correct length of exhaust vent to use.

7.Outside Fresh Air is Mandatory when installing this pellet stove room heater in airtight homes and mobile homes. Be sure that the outside air vent has an approved cap on it to prevent rodents from entering. Be sure to install in location that won’t become blocked with snow, etc.

8.The air intake pipe is equipped with a butterfly valve that is preset to maximum air intake. For optimum operating efficiency you may calibrate the butterfly valve to provide less intake air. (See Figure 7) Caution: Too much restriction on the intake air will cause dirtier burn, therefore, will require more frequent cleaning.

9.Connect the exhaust vent pipe to the exhaust outlet of your pellet stove.

10.Secure all vent joint connections with 3 screws. Seal the exhaust vent joint connections with high temperature silicone sealant.

11.Push the unit straight back to the interior wall, being sure to maintain the minimum clearances to combustibles 6” (152mm) to the back of the unit. Seal the annular space of the wall thimble and around the vent pipe with high temperature silicone sealant.

12.The exhaust vent pipe must extend at least 12” (300mm) out past the exterior wall. Seal the annular space of the wall thimble and around the vent pipe with high temperature silicone sealant.

13.Install an approved horizontal termination cap or if necessary install a 90° elbow and appropriate length of vertical venting. An approved vertical vent cap is recommended.

15

Page 14 Page 16
Page 15
Image 15
United States Stove 5660(I) manual Installing Your Room Heater ‐, Horizontal Exhaust Vent Installation
Page 14 Page 16

5660(I) specifications

The United States Stove 5660(I) is a powerful pellet stove designed to provide efficient heating while boasting modern features and a user-friendly interface. Known for its high performance and reliability, this stove is a popular choice for homeowners seeking an effective heating solution for their living spaces.

One of the standout features of the 5660(I) is its capacity to produce up to 50,000 BTUs, making it suitable for heating areas up to approximately 2,500 square feet. This impressive heating capacity ensures that even larger rooms can be warmed quickly and efficiently, contributing to energy savings and comfort during the colder months.

The stove operates primarily on wood pellets, which are an environmentally friendly fuel choice. Wood pellets are made from compressed sawdust and provide a renewable heating source that burns cleanly and efficiently. The use of pellets not only minimizes emissions but also allows the stove to deliver consistent heat output.

In terms of technology, the United States Stove 5660(I) incorporates advanced features to enhance user experience. The stove is equipped with a digital control panel, offering easy programming options for both heating schedules and temperature settings. This digital interface allows homeowners to customize heating preferences, ensuring a comfortable atmosphere without excessive manual adjustments.

Another notable characteristic of the 5660(I) is its large hopper capacity, holding up to 60 pounds of pellets. This feature extends the time between refueling sessions, allowing for more extended periods of operation without interruption. The stove also features an automatic ignition system, simplifying the startup process and making it convenient for users.

The design of the 5660(I) is not just about functionality; it also boasts an aesthetic appeal. With its sleek and contemporary look, it can seamlessly integrate into various home decors. The stove comes in multiple finishes, allowing homeowners to choose a model that best matches their style.

Safety is also a priority with the United States Stove 5660(I). The unit includes various safety features, including an automatic shut-off function in case of a malfunction, ensuring peace of mind while the stove is in use. The high-efficiency burn system minimizes the amount of ash produced, making maintenance less of a chore.

In summary, the United States Stove 5660(I) combines performance, efficiency, and aesthetic appeal, presenting an excellent heating solution for any home. Its advanced features, ease of use, and eco-friendly fuel choice make it a top contender in the pellet stove market. Whether for heating a large living area or creating a cozy atmosphere, the 5660(I) is a dependable choice.
Top Page Image Contents