INSTALLATION CONFIGURATIONS

Note: Where passage through a wall, or partition of combustible construction is desired, the installation shall conform to CAN/CSA -B365

The Hearth Focus Corn/Pellet Stove Model 6039HF may be installed as follows:

1)A freestanding unit

MOBILE HOME INSTALLATION REQUIREMENTS

IN ADDITION TO THE STANDARD INSTALLATION INSTRUCTION, THE FOLLOWING

REQUIREMENTS ARE MANDATORY FOR INSTALLATION IN A MOBILE HOME:

WARNING

DO NOT INSTALL IN SLEEPING ROOM

1)Stove must be permanently bolted to the floor.

2)Stove must have permanent outside air source. (69FAK)

3)Stove must be permanently electrically grounded to the steel chassis of the mobile home.

4)All vertical chimney vent must have wall supports.

5)All exhaust systems must have a spark arrestor.

CAUTION

THE STRUCTURAL INTEGRITY OF THE MOBILE HOME FLOOR, WALL AND CEILING/

ROOF MUST BE MAINTAINED.

Check with your local building official as other codes may apply.

FREESTANDING STOVE INSTALLATION REQUIREMENTS

General Horizontal Exhaust Termination (Follow manufacturer’s instructions):

1)Locate proper position for the type “PL” wall thimble (F).

2)Use a saber saw or keyhole saw to cut a 7 1/4-inch diameter hole through the wall (E) for a 3-inch pipe. For a 4-inch pipe, cut an 8 1/4-inch hole. Install the wall thimble (F)in the hole. The size of hole opening will vary with brand of wall thimble.

3)Position stove approximately 12” from the wall on the noncombustible floor pad. Push the type “PL” pipe (B) through the wall thimble (D). Squeeze a bead of high temperature RTV silicone sealer (A) around the outside of the 3” diameter exhaust pipe approximately ½” from the stove back panel. Firmly push on a section of type “PL” pipe (B) until the inner pipe liner pushes up against the bead of RTV sealer. Don’t seal the entire 3” diameter pipe as you will not be able to disassemble the pipe at a later date. The bead of silicone will act as a gasket right on the end of the 3” pipe (B). Alternate Method: An approved type “PL” connector back clamp may be used to allow easy disconnect for mainte- nance. (The RTV sealant must be used in mobile home installation)

4)Push stove with pipe attached towards wall. Pipe (B) will go through the wall thimble (F). Be careful not to dislodge the thimble. Position stove not closer than 9” to the wall.

5)Install type “PL” termination cap (G) with rodent screen cap (optional) on outside end or pipe. Note: The end of the exhaust pipe must extend a minimum of 12 inches from the outside of the building. Rodent screen cannot be less than 3/8” opening mesh.

6)If installing with combustion air from outside, cut a separate hole through the wall for the fresh air tube (C). This tube must be 2” minimum diameter pipe. Connect outside air pipe inlet on stove. This tube must be terminated with a 90 degree elbow or hood.

USSC

9

Page 8 Page 10
Page 9
Image 9
United States Stove 6039HF owner manual Installation Configurations, Mobile Home Installation Requirements
Page 8 Page 10

6039HF specifications

The United States Stove 6039HF is a high-efficiency, modern wood-burning stove designed for homeowners seeking to enhance their heating efficiency while minimizing their environmental impact. This unit is particularly known for its cutting-edge features and superior performance, making it a popular choice among eco-conscious consumers.

One of the key features of the 6039HF is its high-efficiency rating, which allows it to generate heat using minimal wood. This stove is outfitted with a secondary combustion system, which enhances the burning of gases and particulates, resulting in reduced emissions. Thanks to this technology, the 6039HF achieves an impressive efficiency rate that often exceeds 80%, making it one of the more environmentally friendly options on the market.

The stove's design incorporates an air wash system, which maintains clean glass for an unobstructed view of the fire. This feature not only adds to the aesthetic appeal of the 6039HF, but it also contributes to a cleaner burn by keeping the glass clear of soot and creosote buildup.

In terms of construction, the United States Stove 6039HF is built with high-quality materials intended for durability and longevity. The stove's firebox is constructed from heavy-duty steel, allowing it to withstand high temperatures and ensuring a long lifespan. Additionally, the large viewing window is crafted from high-temperature ceramic glass, which is designed to withstand the intense heat generated during operation.

The versatility of the 6039HF is another selling point. It is capable of heating areas up to 2,000 square feet, making it suitable for various spaces, from large living rooms to expansive cabins. With a heating capacity of up to 75,000 BTUs, it can effectively keep a home warm during the coldest months.

Moreover, the 6039HF features an easy-to-use ash removal system, which simplifies maintenance. The integrated ash pan collects debris, making it easy for users to clean and maintain the stove, ensuring optimal performance over time.

Overall, the United States Stove 6039HF combines efficiency, durability, and user-friendly features, making it an excellent choice for those looking to heat their spaces sustainably and effectively. With modern technology and robust construction, this wood stove is an investment in both comfort and eco-friendliness.
Top Page Image Contents