•The water heater must NOT be placed on its side. It should be transported and stored in an upright position.

•Remove exterior packaging and place installation components aside.

•Inspect all parts for damage prior to installation and start-up.

•Completely read all instructions before attempting to assemble and install this product.

•After installation, dispose of/recycle all packaging materials.

Location Requirements

Site location

Select a location near the center of the water piping system. The unit must be installed indoors and in a vertical position on a level surface. The flooring beneath the water heater must be able to support the weight of the water heater when filled with water (967 lbs. full).

IMPORTANT: The water heater must be located in a space 750 cubic feet or larger, and must have unrestricted airflow. As an example, a room that has an 8 foot tall ceiling and is 10 feet long by 9-1/2 feet wide would contain 760 cubic feet.

NOTE: For optimal efficiency and serviceability, the

following clearances should be maintained: 3 feet on the air inlet side, 5 feet. on the air outlet side, 6 inches in the back, and 2 feet in the front.

The water heater should be located in an area not subject to freezing temperatures. Water heaters located in unconditioned spaces (i.e., garages, basements, etc.) may require the water piping, condensate piping, and drain piping to be insulated to shelter against freezing. The drain and controls must be easily accessible for operation and service.

The site location must be free from any corrosive elements in the atmosphere such as sulfur, fluorine, and chlorine. These elements are found in aerosol sprays, detergents, bleaches, cleaning solvents, air fresheners, paint, and varnish removers, refrigerants, and many other commercial and household products. In addition, excessive dust and lint may affect the operation of the unit (See “Cleaning the Filter” section).

The ambient air temperature must also be considered when installing this unit. In Efficiency Mode the ambient air temperature must be above 45°F and below 109°F. If the ambient air temperature falls outside these upper and lower limits the electrical elements will activate to meet the hot water demand and the heat pump does not operate.

NOTE: Local codes and requirements in your area may require the installation of your water heater be accomplished in a way that the bottom element is elevated from the

floor at least 18 inches. Ensure that a platform capable of supporting the combined weight of the water heater and water (967-pounds) is used.

IMPORTANT: The water heater should be located in an area where leakage of the tank, connections, condensate lines or condensate will not result in damage to the area adjacent to the water heater or to lower floors of the structure. Due to the normal corrosive action of the water, the tank will eventually leak after an extended period of time. Also, any external plumbing leak, including those from improper installation, may cause early failure of the tank due to corrosion if not repaired. If the homeowner is uncomfortable with making the repair a qualified person should be contacted. A suitable metal drain pan should be installed under the water heater as shown below, to help protect the property from damage which may occur from condensate formation or leaks in the piping connections or tank. The pan must limit the water level to a maximum depth of 2-1/2 inches and be two inches wider than the heater and piped to an adequate drain. Locate the water heater near a suitable indoor drain. Outside drains are subject to freezing temperatures which can obstruct the drain line. The piping should be at least 3/4” ID and sloped for proper drainage. Under no circumstance will the manufacturer or seller of this water heater be held liable for any water damage which is caused by your failure to follow these instructions.

Figure 2

Metal Drain Pan Installation

METAL

DRAIN

PAN

PIPED TO AN

ADEQUATE DRAIN

AT LEAST 2” GREATER THAN THE

DIAMETER OF THE WATER HEATER.

NOTE: The water heater shall be located so it is not subject to physical damage by moving vehicles or area flooding.

Figure 3

 

Residential Garage

 

Installation

 

 

Vehicle

 

Stop

Drain

Drain

Pan

 

State of California

NOTE: The water heater must be braced, anchored, or strapped to avoid moving during an earthquake. Contact local utilities for code requirements in your area, visit http://www.dsa.dgs.ca.gov, or call 1-916-445-8100 and request instructions.

4

Page 3 Page 5
Page 4
Image 4
Univex EPX-80DHPT, 318258-000 installation instructions Location Requirements, Site location
Page 3 Page 5

318258-000, EPX-80DHPT specifications

The Univex 318258-000, also known as the EPX-80DHPT, is a highly advanced pizza and baking oven carefully designed to meet the rigorous demands of commercial kitchens. Its innovative features, robust technologies, and user-friendly characteristics make it an essential piece of equipment for pizzerias, bakeries, and food service establishments.

One of the standout features of the Univex EPX-80DHPT is its dual heating system. This system combines both convection and radiant heat, ensuring even cooking and optimal baking results for a variety of dishes. The convection aspect promotes efficient airflow, allowing for uniform heat distribution, while the radiant heat emphasizes crispiness and browning, making it perfect for achieving that perfect pizza crust.

The oven's chamber is spacious, providing ample room to cook multiple pizzas simultaneously, which is a significant advantage during peak service hours. It has a baking capacity of up to 8 pizzas at a time, depending on their size, catering to busy restaurants and catering events effectively. Furthermore, the high-temperature capabilities of the EPX-80DHPT make it suitable for a wide range of baking applications, including artisanal bread, cookies, and pastries.

The Univex EPX-80DHPT is designed with user convenience in mind. Its digital control panel is intuitive and easy to navigate, allowing chefs to set precise cooking temperatures and times. The built-in timer and temperature control help ensure consistent results, minimizing the risk of overcooking or undercooking. With the ability to set temperatures up to 650 degrees Fahrenheit, this oven is versatile enough to accommodate various cooking styles and recipes.

Durability is another hallmark of the Univex EPX-80DHPT. Constructed with high-quality stainless steel, this oven is built to withstand the rigors of daily use in busy kitchens. Its solid construction not only ensures longevity but also facilitates easy cleaning and maintenance.

In summary, the Univex 318258-000, EPX-80DHPT, combines advanced technology, user-friendly features, and robust construction to deliver a top-tier baking solution for any commercial kitchen. With its impressive cooking capabilities, intuitive controls, and durable design, this oven stands out as an essential asset for those who prioritize quality and efficiency in their culinary offerings.
Top Page Image Contents