®

NATURAL GAS RESIDENTIAL HEATERS

INSTALLATION

Continued

Attaching To Wall Anchor Method

For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry).

1.Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1" deep.

2.Fold wall anchor as shown in Figure 14.

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

4.For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings.

IMPORTANT: Do not hammer key! For thick walls (over 1/2" thick) or solid walls, do not pop open wings.

5.Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors.

6.Insert mounting screws through bracket and into wall anchors.

7.Tighten screws until mounting bracket is firmly fastened to wall.

Placing Heater On Mounting Bracket

1.Locate two horizontal slots on back panel of heater.

2.Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mounting bracket.

Horizontal Slots

Stand-Out

Tab

Mounting Bracket (attached to wall)

Figure 16 - Mounting Heater Onto Mount- ing Bracket

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see Figure 17).

2.Mark screw locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screws into hollow or solid wall, install wall anchors. Follow steps 1 through 4 un- der Attaching To Wall Anchor Method. If installing bottom mounting screw into wall stud, drill holes at marked lo- cations using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacers between bottom mount- ing holes and wall anchor or drilled hole.

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten both screws until heater is firmly secured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see pages 12 and 13).

Figure 14 - Folding Anchor

Figure 15 - Popping Open Anchor Wings For Thin Walls

Figure 17 - Installing Bottom Mounting Screws

10

104431

Page 9 Page 11
Page 10
Image 10
Vanguard Heating VMH3000TN installation manual Placing Heater On Mounting Bracket, Installing Bottom Mounting Screws
Page 9 Page 11

VMH3000TN specifications

The Vanguard Heating VMH3000TN is a state-of-the-art heating solution designed to deliver efficient warmth and comfort in a variety of environments. Its innovative features and advanced technologies make it an ideal choice for both residential and commercial applications.

One of the standout features of the VMH3000TN is its powerful heating capacity. With a substantial output, this unit can quickly warm large spaces, ensuring that every corner of the room reaches a comfortable temperature. This makes it perfect for homes, offices, workshops, and other facilities that require reliable heat distribution.

The VMH3000TN comes equipped with advanced energy-efficient technology. It incorporates a high-performance heat exchanger that maximizes thermal efficiency, helping to reduce energy consumption and lower heating costs. This makes it an environmentally-friendly option for consumers looking to minimize their carbon footprint while enjoying the benefits of effective heating.

Another notable characteristic of the VMH3000TN is its user-friendly interface. The product features intuitive controls that allow users to customize their heating experience easily. With programmable settings, users can set specific heating schedules according to their lifestyle, ensuring that spaces are warm when needed without excessive energy use.

Safety is also a priority in the design of the VMH3000TN. It is equipped with multiple safety features, including overheat protection and a reliable thermostat. These systems work together to prevent potential hazards, giving users peace of mind while using the heater.

Durability and reliability are additional attributes of this model. Constructed with high-quality materials, the VMH3000TN is built to withstand the rigors of daily use. Its robust design ensures longevity, making it a worthwhile investment for those seeking a long-term heating solution.

The VMH3000TN is also designed with versatility in mind. Its sleek and compact design enables it to fit seamlessly into a variety of spaces and decor styles. It can be easily installed in homes, garages, or offices without taking up excessive space.

In summary, the Vanguard Heating VMH3000TN is a powerful, efficient, and reliable heating solution that caters to diverse heating needs. Its array of features, safety mechanisms, and user-friendly operation make it a top choice for consumers seeking effective climate control. Whether for personal comfort or professional use, the VMH3000TN promises to deliver warm and inviting spaces all winter long.
Top Page Image Contents