OWNER’S MANUAL

INSTALLATION

Continued

THERMOSTAT SENSING BULB

The thermostat sensing bulb has been placed insidetheheaterforprotectionduringshipping.

Locating Thermostat Sensing Bulb

1.Remove front panel of heater (see Fig- ure 2, page 3).

2.Locate thermostat sensing bulb just under burner assembly.

IMPORTANT: Attach thermostat sensing bulb to back of heater for proper operation.

INSTALLATION OPTIONS

There are three options for mounting this heater.

A.Mounting heater to wall

B.Mounting heater to optional hearth base

C.Mounting heater to optional mantel (some mantels require the hearth base)

A. MOUNTING HEATER TO WALL

Mounting Bracket

The mounting bracket is located on back panel of heater. It has been taped there for shipping. Remove mounting bracket from back panel.

Marking Screw Locations

1.Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is level.

WARNING: Maintain minimum clearances shown in Figure 13. If you can, provide greater clear- ances from floor and joining wall.

2.Mark screw locations on wall (see Fig- ure 13).

Note: Only mark last hole on each end of mounting bracket. Insert mounting screws through these holes only.

3.Remove tape and mounting bracket from wall.

Attaching Thermostat Sensing Bulb

1.Remove thermostat sensing bulb from holders inside heater. Route through slot opening in bottom of heater.

2.Place clamp on thermostat sensing bulb as shown in Figure 11. Clamp is pro- vided in hardware package.

3.Snap clamp into upper mounting hole as shown in Figure 11. Mounting hole is located on lower left edge on back of heater. Make sure the thermostat sensing bulb is pointing up.

Thermostat

Sensing Bulb

Clamp

Figure 11 - Attaching Thermostat Sens- ing Bulb

Mounting

Bracket

Figure 12 - Mounting Bracket Location

Methods For Attaching Mounting Bracket To Wall

Only use last hole on each end of mounting bracket to attach bracket to wall. These two holes are 16 inches apart from their centers. Attach mounting bracket to wall in one of two ways.

1.Attaching to wall stud

2.Attaching to wall anchor

Attaching To Wall Stud: This method pro- vides the strongest hold. Insert mounting screws through mounting bracket and into wall studs.

Attaching To Wall Anchor: This method allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry).

Decide which method better suits your needs. Either method will provide a secure hold for the mounting bracket.

11"

16"

Min.

 

AdjoiningWall

 

Only Insert Mounting

20 3/4"

Screws Through Last

Min.

Hole On Each End

 

Floor

Figure 13 - Mounting Bracket Clearances

Attaching Mounting Bracket To Wall

Note: Wall anchors, mounting screws, and spacers are in hardware package. The hard- ware package is provided with heater.

Attaching To Wall Stud Method

For attaching mounting bracket to wall studs.

1.Drill holes at marked locations using 9/64" drill bit.

2.Place mounting bracket onto wall. Line up last hole on each end of bracket with holes drilled in wall.

3.Insert mounting screws through bracket and into wall studs.

4.Tighten screws until mounting bracket is firmly fastened to wall studs.

Continued

104431

9

Page 9
Image 9
Vanguard Heating VMH3000TN installation manual Thermostat Sensing Bulb, Installation Options, Mounting Heater to Wall

VMH3000TN specifications

The Vanguard Heating VMH3000TN is a state-of-the-art heating solution designed to deliver efficient warmth and comfort in a variety of environments. Its innovative features and advanced technologies make it an ideal choice for both residential and commercial applications.

One of the standout features of the VMH3000TN is its powerful heating capacity. With a substantial output, this unit can quickly warm large spaces, ensuring that every corner of the room reaches a comfortable temperature. This makes it perfect for homes, offices, workshops, and other facilities that require reliable heat distribution.

The VMH3000TN comes equipped with advanced energy-efficient technology. It incorporates a high-performance heat exchanger that maximizes thermal efficiency, helping to reduce energy consumption and lower heating costs. This makes it an environmentally-friendly option for consumers looking to minimize their carbon footprint while enjoying the benefits of effective heating.

Another notable characteristic of the VMH3000TN is its user-friendly interface. The product features intuitive controls that allow users to customize their heating experience easily. With programmable settings, users can set specific heating schedules according to their lifestyle, ensuring that spaces are warm when needed without excessive energy use.

Safety is also a priority in the design of the VMH3000TN. It is equipped with multiple safety features, including overheat protection and a reliable thermostat. These systems work together to prevent potential hazards, giving users peace of mind while using the heater.

Durability and reliability are additional attributes of this model. Constructed with high-quality materials, the VMH3000TN is built to withstand the rigors of daily use. Its robust design ensures longevity, making it a worthwhile investment for those seeking a long-term heating solution.

The VMH3000TN is also designed with versatility in mind. Its sleek and compact design enables it to fit seamlessly into a variety of spaces and decor styles. It can be easily installed in homes, garages, or offices without taking up excessive space.

In summary, the Vanguard Heating VMH3000TN is a powerful, efficient, and reliable heating solution that caters to diverse heating needs. Its array of features, safety mechanisms, and user-friendly operation make it a top choice for consumers seeking effective climate control. Whether for personal comfort or professional use, the VMH3000TN promises to deliver warm and inviting spaces all winter long.