Viking PHKDFSB5 Handle Installation, Installation with Wooden Full Overlay Custom Door Front

IMPORTANT–Please Read and Follow! Handle Installation

•Before beginning, please read these instructions completely and carefully.

•Use caution during assembly to minimize scratches.

•Do not remove permanently affixed labels, warnings or plates from the product. This may void the warranty.

•Please refer to the DFSB5, DFBB5 or DFBB Installation Instructions for more information on installing the refrigerator door panel.

•The installer should leave instructions with the customer who should retain for local inspector’s use and future reference.

Installation with Wooden Full Overlay Custom Door Front

Parts Included

Part	Quantity
Professional Series Handle Tubes	(2)
Professional Series End Caps	(4)
1/4” x 1” Phillips Head Screws	(8)
Installation Instructions

Required Tools

Electric Drill

5/16” (.8 cm) Drill Bit

5/8” (1.6 cm) Spade or Forstner Bit (Counterbore) Tape Measure

Phillips Head Screwdriver

Masking Tape and Pencil

17-15/16”

(45.6 cm)

27-1/2”

(69.9 cm)

1-3/8”

(3.5 cm)

1-9/16”

(4.0 cm)

5/16” (.8 cm) through-holes with 5/8” x 1/4” counterbore *See section A-A.

A A

9”
(22.9 cm)	5/16” (.8 cm)
	through-holes
	with 5/8” x 1/4”
	counterbore
	*See section A-A.
34-11/16”
(88.1 cm)
A	A
1-3/8” (3.5 cm)
1-9/16” (4.0 cm)
C
L
1-3/8”
(3.5 cm)
1-9/16” (4.0 cm)
31-11/16” (80.5 cm)

Rubber Mallet

To Install:

1.	Locate the wooden custom panel.
2.	Using the illustrations on the next page, layout the handle location on the panels. It is
	recommended that masking tape be placed where the four holes will be drilled to help mark
	the hole placement and to prevent any damage to the door when drilling the holes.
3.	Each Professional Series handle will be mounted using (4) of the 1/4” x 1” Phillips head
	screws provided. Using the 5/16”(.8 cm) drill bit, drill completely through the door in the
	hole locations. Using the 5/8” (1.6 cm) bit, counter-bore two holes 1/4” (.6 cm) deep on the
	BACKSIDE of the custom door panel.
4.	Place a handle end cap on both ends of the handle tube. Tap the endcaps firmly into place
	with a rubber mallet ensuring that both endcaps mounting surfaces are parallel.
5.	Align the holes in the endcaps with the holes on the panel and attach the Professional
	handle to the panel using the (4) 1/4” (.6cm) screws provided.

Custom Door

DFSB5 Side-by-Side (Front View)

Professional Series Handle

Section A-A

Professional Series Handle

(Applies to DFSB5/DFBB5 Only)

5/8” (1.6 cm) Ø x 1/4” (.6 cm) counterbore

1-3/8”(3.5 cm)

5/16” (.8 cm) Ø through-holes

3/4” (1.8 cm)

Full Overlay Panel

Custom Door

DFBB5/DFBB Bottom Mount (Front View)

Professional Series Handle

Section A-A

Professional Series Handle

5/8” (1.6 cm) Ø x 1/4” (.6 cm) counterbore

1/4” (.6 cm)	1-3/8”(3.5 cm)
Base Panel

5/16” (.8 cm) Ø through-holes

3/4” (1.8 cm)

Full Overlay Panel

6. Repeat steps 1 - 4 to attach other handle.

Specifications subject to change without notice.

2 3