IP3111/IP3121 Users Manual
NetworKam
Before You Use
Hardware installation
Table of Contents
Package Contents
How to Install
Authentication
How to Use
Software configuration
First access to NetworKam
Telnet
URL commands of NetworKam
Appendix
A. POST procedure
B. Frequently asked questions
C. Technical specifications
NetworKam IP3111/IP3121 Power adapter Null modem cable
Package Contents
I/O terminal block connector
Warranty card
Wrench Installation and document CD Quick installation guide
COM port
Physical Description
Rear Panel
Ethernet 10/100 socket
General I/O terminal block
Status LEDs
Power adapter
Restore button
Auto Iris Lens Connector
How to Install
Ethernet Environment
Hardware installation
Cable connection
Power on
Easy way with installer program
Software configuration
The IP address shown in Current IP Address field is for the administrators reference. If the administrator wants to use another IP address, modify the IP text field below the list window
When IP and options are O.K., click on . A message window will pop open to inform if the IP address is valid
on to access the newly installed server in the default browser
While checking “Use this IP whenever system boots”, a dialog window may pop out to ask for “Server FTP Port” and “Root Password” because they are already changed to other than default settings. If the settings are lost, restore default settings and use installer to install again
Manual way with existing programs
First access to NetworKam
the previous settings. If the install option stays checked, NetworKam will perform the installation procedure every time the system boots up
Hardware installation
Modem Environment
utility power outlet. It will reduce accidental electric surge shock
Power on
Cable connection
Software configuration
Install a new modem
Open the control panel and double click the modems icon
Check Dont detect my modem...... item and click on
to install a new modem
Choose the serial port that the included null modem cable is attached to and click on . The null modem is now ready for use
Setup a new connection
Just enter arbitrary digits as phone number and click on . The phone number used here is not important
Right-click on the newly setup connection icon for properties
Select 115200 as the speed and click on
Double click the newly setup connection. A dialing information window will pop up. Enter “root” as user
Through direct connection by null modem cable administrators can open the default web browser and type in 200.1.1.1 as the address and press enter. Note that 200.1.1.1 will be the default IP address in a dial-in connection and 200.1.1.100 will be the given IP address for the users PC by NetworKam. The user name and password are the same as what was entered during installation
First access to NetworKam
basic configurations. If people other than the administrator will be allowed to use NetworKam, the administrator should add these user profiles in the Security option. When NetworKam accepts dial-in connection and acts as a server, the user name and password used in dialing are the same as what was stored in the user database managed for web access. Any managed user can be authorized during PPP negotiation and access web pages. However only administrators can access the configuration page
How to Use
Authentication
If it is initial access to NetworKam in Windows, the web browser will ask to install a new plug-in that is provided by NetworKam. This plug-in has been registered for certificate and is used to display the
Main screen with camera view
Primary user’s capability
Pan/Tilt positioning device control
Client Setting
NetworKam is the domain name or original IP address of NetworKam
url http//NetworKam/setup/config.html
System configuration
System parameters
User group administration
Network settings
subnet mask may differ from the default value 255.255.255.0 and service providers may assign some specific network settings. Administrators should change the configuration according to what is given by the service provider. The configuration may include IP address, Subnet Mask, Default Router, Primary DNS and Secondary DNS. After changing network settings, be sure to leave Reset network at next boot blank to skip installation when the system restarts. Otherwise the settings will be erased
the client side will receive the poor quality of media. For improving this situation, you can check the “Improve audio quality in low bandwidth environment” item. It can make the audio quality better, but the media delay is longer and real-time issue is bad. If the network performance is worst, please select the ”UDP protocol“ as the communication protocol in “client setting”
Video codec parameters
IP3111/IP3121 uses MPEG4 codec compression for best streaming solution. The compressed video data is far less than JPEG in normal cases but it still depends on the level of difference between every two sequential images. There are three dependent parameters provided for adjustment. Maximum Frame Rate limits the maximal refresh frame rate that can be combined with the Video Quality Control to optimize the bandwidth utilization and video quality. If users want to fix the bandwidth utilization regardless of the video quality, choose Fix Bit Rate and select the desired bandwidth. The video quality may be poor in order to send maximal frames within the limited bandwidth when images change drastically. Consequently to ensure the video quantization rate regardless of the bandwidth, it will utilize more bandwidth to send the maximal frames when images change drastically
To adjust image settings for best visual quality, press and a motion picture window will pop up for your reference. There are four fields including Brightness, Contrast, Hue and Saturation for video compensation. . Each field has eleven levels ranged from -5 to +5. The user may
Motion detection
Page
Camera positioning device configuration
the commands and click on to close the command setting window
Modem and dialup settings
minutes will force NetworKam to drop the connection when there is no activity on the connection for the specific period. The range of this period is from 1 to 240 minutes, with 0 indicating a continuous connection. Administrators may let NetworKam keep the connection for a while to allow connections from outside. The IP address given by the ISP can be taken from the connection log that is mailed or uploaded when dial-up connection is successful. Setting the value to zero will make NetworKam always keep the connection
Application
The other Event operation can be used to combine motion detection with devices attached to digital input, to drive devices attached to digital output, or send out snapshots for evidence. It helps users establish an easy security system. Administrators may choose any combination of conditions to form special applications according to their personal needs. NetworKam will continuously monitor the channel and digital input every half second. Once the user-defined conditions are matched, NetworKams will capture three stages of events and react based on the Trigger action settings. The post-event snapshot can be configured to be delayed after events happen according to the setting in Take snapshot at seconds after event. The three stages of snapshots will be VPRE.JPG, VTRG.JPG and VPOS.JPG. Since the same event may exist for a while, administrators can set delay time in Delay seconds before detecting next event to reduce multiple triggers by the same event
Homepage layout settings
One-shot fast configuration via FTP
0002D1000001
The followings are as same as above
user password
0 0002D1000001Initial value is as same as serial number
String shorter than 15 character s
logo type
primary name server
1200k , 1000k , 768k , 512k , 384k , 256k , 128k , 64k
or RS485
1, 2, 3, 5, 10, 15, 20, 25, 30 30 for NTSC only
RIGHT
PT control commands UP
DOWN
LEFT
Viewing system parameters
Restore factory default settings
Advanced functions
Viewing system log
Customizing homepage images
Uploading snapshots periodically to an external FTP server
Viewing system log
Uploading the configuration file
Software revision upgrade
3. Connect to NetworKam with user name as “root” and password
web page in the browser
Stop information dumping
Telnet
System core debugging
Monitor changed status of digital inputs
Set digital outputs
Skip installation during the next boot
Reset network for new settings
Reset system
Drive digital outputs
URL commands of NetworKam
Capture update Snapshot of JPEG image
Move motorized device in PT direction
Restore factory default settings
Restart system
setup/restore.cgi
Page URL
text string shorter than 15 characters
General format of command URL
System configuration URL
System resource URL
Network configuration URL
Security configuration URL
Video configuration URL
Image quality configuration URL
Camera custom command configuration URL
Camera configuration URL
Application configuration URL
Modem configuration URL
Homepage layout configuration URL
Possible failed component
A. POST procedure
Appendix
LED pattern after POST
B. Frequently asked questions
Q. How does NetworKam detect the supported PTZ cameras automatically?
Q. How fast will NetworKam check the status of digital inputs?
C. Technical specifications
web site
Electromagnetic Compatibility EMC
Liability
Vivotek Inc
